Search results for: 'grai 8 drops bar door hidden'

Global partitions 8" wrap door kit for Solid Plastic material. Comes in anodized aluminum finish and are for 1" thick material only. You will need to choose in or out swing when ordering. Can be used as right or left hand as hinges are field reversible. This is done by taking the 3 pieces apart and reconfiguring the opposite swing. See manufacturers numbers listed below. Used with Global and Accurate partitions.

Inswing Door Kit: 40-8441007

Outswing door Kit: 40-8441008

Push Bar Adjustable 454

Finishes:
US26/625 polished chrome
US26D/626 brushed chrome
US3/605 polished brass
US4/606 brushed brass

Material: Brass
Material Size: 1" round tube adjustable up to 36"
Base: 2" round x 2-1/2"
Clearance: 1-1/2"
Projection: 2-1/2"

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Latch finger 701730 included, uses 700308-700309 handle assembly. Also known as 7119281, 75136, 2837, 70063, rs3624, lr136.

Restroom Door Kit Inswing 7/8" Door & 1-1/4" Post Cast SS. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 17803.

Sargent 60/80 Push Bar Pin Retaining Clip

used on Sargent 60 and 80 series to retain the push bar and channel axles. Use with the 68-0229 and 68-0230.

Sargent part # 01-0098

Two person latch bar 1962-1970 9-9/16"length

Sargent 60/80 Push Bar Pins-Short Pin

Also known as the push bar axle, this is the pin that you see on the push pad.

1-9/16" LONG

Sargent part # 68-0229

Latch finger 701730 included, uses 700308-700309 handle assembly. Also known as 7119280, 75130, 2831, 70062, rs3018, lr130.

Interior Steel Equipment Locker Expanded Metal Lock bar for 36" double tier locker. Used in 1965 - 1994. Also known as 2636, is4016. This lock bar was used with a locker turn handle, the turn handle  connected to the lock bar creates the bars to retract or expanding locking at the top and bottom of the locker to lock it.

Grab Bar Installation Kit Exposed Masonry Wall screws and anchors

1-1/4" diameter materal
Offset Door Handle
Establish the center to center dimension by subtracting the width of one stile from the width of the door. On solid doors, subtract 5" from the width of the door.

Please specify either wood or metal door, and its thickness; we'll supply
appropriate fasteners.

Please allow 3-4 weeks on the Dark Bronze and Aluminum, and 2 weeks on the other finishes

Finishes

Von Duprin Push Bar Guide 090049

Fits on the end of the push bar assembly, reduces noise and friction. Used on the Von Duprin 33A, and 99 / 98's

Von Duprin Part # 090049
Old Von Duprin Part # 971993

Doromatic 2390 Push Bar Anchor Brk

Doromatic / Falcon Part # PB335 or BRKT.137

Grab Bar Installation Kit Concealed Wood Backing, wood screws only.

A.W. Anderberg 301AL 4 Bar Window HInge, aluminum construction.

29/32" width x 5/8" stack height

Found in commercial aluminum framed hopper windows.

10" and 12" only, if you have an older larger size, please use the A.W. Anderberg 301ST or A.W. Anderberg 301SS as a replacement. You might have to shim the tracks in these cases, because the stack height is lower on the steel and stainless steel hinges. A.W. Anderberg no longer makes the larger sizes of the Aluminum Hinges due to the brittle nature of aluminum.

Sold individually, we recommend changing both hinges with you are replacing the hinge.

6-20-2012 No longer manufactured, what we have in stock, is what we have. You will have to replace with 301ST or 301SS Hinges

Door Pull 26 1" Diameter

This door handle is made of 1" round stock in either solid, aluminum, brass or stainless steel. It comes standard with thru bolts and finish washers, but can be special ordered if you would like the handle mounted back to back or surface mounted. Also known as a Door Handle or Door Grip.

1" diameter material
2-3/4" projection

Finishes

8" GDP810
10" GDP101
12" GDP121

The Detex ECL-230D Alarmed Exit Device is a battery operated, rugged deadbolt panic device. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm.  Rim Cylinder is not included.

If you have a door that requires Panic Hardware, then use the ECL-230D-PH

Hussey Bleacher Auto Stop Bar Right Hand. Also known as 1002075.

The 220-2520 is the Grit Stripped version of the 7850R Service Weight Smooth Rubber Treads.  The 220 comes with two 3/4" grit strips, the 2520 would be the visually impaired version with one 2" wide strip. The treads are 1/8" thick along the entire depth of the treads, and have a nose that drops down 1-9/16". They are designed for interior use.

Grab Bar Installation Kit Exposed for Wood Backing, Wood screws are included.

Partition Strike And Keeper For 1" Door, 1-7/8" Between Screws, Stamped Stainless Steel

Stamped stainless steel .075" thick construction. The strike and keeper measure 2-7/8" high by 2" wide with a 1-7/8" hole spacing. The stop posts are 5/8" wide by 7/8" tall with rubber inserts. For use with 1" square edge posts. Also known as a Bathroom Stall Strike and Keeper Outswing 1". Manufacture part # 6459.

Shipped with mounting screws.

Grab Bar Installation Kit Exposed 1" Panel ss plate with screw and nut.

Detex EAX-500W Weatherized Door Exit Alarm

The Detex EAX-500W Series is designed for applications requiring a battery-powered alarm on secured doors. The alarm, with approximately 100dB, will sound when an unauthorized exit occurs. The redesigned shape and smaller size of the EAX-500W makes it the ideal choice for quick and easy installations on emergency exit and restricted doors.  The Weatherized version of the EAX-500 is designed for out swinging doors that may get wet, or damp environments.

Gray Only

Mortise cylinder sold separately
Powered by a 9 volt battery

Detex EAX-500 Installation Instructions

Interior Steel Equipment Upper Locking Bar For 2 person lockers. Includes Latching. Also known as 35701, 3530, 76016, is4409, LIN411.

The Jackson 1285/1295 Push Bar End Cap Package comes complete with the right and left side caps, mounting bracket and screws.  This piece is available in aluminum (silver) and dark bronze (dark brown).

Jackson Part # 30-2650

Medart Bleacher Top Bar Only for front row truck assembly.

The Detex ECL-230D-PH Alarmed Exit Device is a battery operated, rugged deadbolt panic device, and is UL-Listed Panic Hardware for 36" to 48" doors. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force, and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm. Rim Cylinder is not included.

The GS780R Rubber Stair Tread is a Raised Disc.  It features an adjustable nose that drops down 1-9/16".  The nose is 1/8" thick.  You have two choices on the Grit Stripping, the Visual Impaired 1-2" wide or 2-3/4" wide grit tape strips. They are designed for interior use.

Lyon Metal Locker 30" Expanded Metal Lock Bar, Used in March 1973 - Current. Also known as 676630.

Universal Bleacher Trip Bar.

The 7520R is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Square Nose, for Round Nose search 7520RRD. The treads are 1/8" thick along the entire depth of the treads, and have a nose that drops down 1-9/16".  For the Grit Stripped version you would order the 220 or the 2520.  The 220 comes with two 3/4" grit strips, the 2520 would be the visually impaired version with one 2" wide strip. They are designed for interior use.

Toilet Partition Bottom Hinge Assembly For 7/8" Door To 1-1/4" Pilaster Square Edge Cast Stainless Steel

Cast stainless steel hinge. Hinge mounts to 1-1/4" square edge post or pilaster, for use with 7/8" thick doors. Kit includes bottom hinge, pintle, pin and insert. Also known as a Bathroom Stall Bottom Pivot Hinge Set. Manufacture part # 63013

Includes all screws.