Search results for: 'grey 8 door braced door horn'

Bobrick B-4369 recessed paper towel dispenser with waste receptacle in a satin finish stainless steel. The unit holds 350 c-fold towel or 475 multifold towels. Leak-proof waste container has a 3 gal. capacity. Removable front panel for cleaning. Wall opening 11-38"w x 26-5/8"ht x 4" minimum depth.

Von Duprin 360L Lever Trim

The Von Durpin 360L Lever Trim has a base measurement of 7-1/2" high by 1-11/16" wide and 7/8" thick. The lever is 4-1/2" and projects out 3". This lever Trim uses a 1-1/4" Mortise Straight Cam Cylinder.

Von Duprin Part # 360L

The Monarch / Dor-O-Matic / Falcon 600339 NL Spring Package converts the 179L , 712L, 712K, 912l and 911K to an NL function.   The NL function is  one were the Lever Handle can not be unlocked and left in the unlocked position when the key is removed.   Spring has a 5/8" diameter.  See attached instructions.

Shower Curtain - 10 Ga. White Vinyl, Order 8 Hooks Separately - 48"W X 72"H

Flame-resistant, anti-bacterial, 10 gauge white vinyl fabric with standard height of 72". Curtain should be 6" wider than opening up to 54" and 12" wider than opening exceeding 54".

Shower curtain should be attached with hooks (not provided, order separately) to rod (not provided, order separately). Known as 10-1200-V48 by American Specialties.

Concealed Partition Latch Keeper Bumper Inswing Cast Stainless Steel

Stainless steel casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5653.

Shipped with mounting screws.

Chrome Plated Toilet Partition Flat Stop Keeper

Polished chrome plated Zamac construction. The keeper base is 2-1/2" tall by 1-3/32" wide. The latch face measures 2-1/2" tall with a 7/8" projection. The hole spacing is 1-1/2". The slot measures 5/16" by 1-9/16". Also known as a Bathroom Stall Keeper-Inswing Flat. Manufacture part # 5160.

Shipped with mounting screws.

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Toilet partition round edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1-1/4" thick by 3" high. This size pilaster post shoes are split on one end for easy installation. Also known as a Bathroom Stall Pilaster Post Shoe Round Edge. Used for the base of the support system with pilaster mounting.

The Command Access MLRK1-VD22 is a motorized electric latch retraction with REX for the Von Duprin 22.  This motor is 24 to 28 volts and has a Standard : 900 mA (Avg Current Peak); 215 mA (Avg Current Hold). This unit requires 18 ga wire.  And ships with (1) Motor Mount with MM5; (2) 40002 - 8/32 x 1/4 inch Phillips Head Screw; (1) 50030 8/Lead with vd Connector; (1) 50944 Molex Pigtail; (1) 40144 Dogging Hole Cap; (1) 50991 Fire Rated Drilling Template; (1) Replacement Dogging Tail Piece.

The MLRK1-VD22 is a cost-effective and straightforward way to upgrade your Von Duprin 22 series device to motor-driven latch retraction in the field. UL Listed + 3 Year Warranty

Hardware packets are based on 4' x 8' boards.

Package includes 4 plastic anchors, 4 of the #2LCLIPS, 4 drill and tap screws, and 4 of the #10 phillips screws.

HD-408-BB is used for boards with item # prefixes: AA, AB, AF, AM, AN, AP, CA, CB, CT, CW, LA, PR, WB, WF, WN, WP

The Von Duprin 090039 is used in the push bar assembly to return the latch. It is known as the Base Plate Latch Return Spring or Latch Return Spring. It is used on the 22, 33A, 35A, 98 and 99 Devices. The spring is 2-1/4 inch long with a 3/8 inch diameter.

Partition Headrail Bracket for 1 1/4" Headrail

Chrome plate Zamac die cast construction. The overall measurements of the bracket are 3-3/32" wide by 1-19/32" high by 1" deep with a hole spacing of 2-3/8". The spread for the headrail is 1-7/16" wide by 1-19/32" deep. Also known as a Bathroom Stall Headrail Bracket. Manufacture part # 2170.

Shipped with screws.

Selling Bobrick channel frame plate glass mirrors. Type 430 stainless steel with bright polished finish with mitered corners. Frame screw permits easy replacement of glass. 1/4" thick glass mirror with 1/2"x1/2"x3/8" stainless framing. Secured to concealed wall hanger with theft resistant mounting. Known as the B-165 series channel frame mirrors.

The Matte Black Hadrian Two Ear Bracket is constructed of stainless steel and measures 3-1/8"Wx1-1/4"Hx47"L. This two ear bracket is designed for 1/2" thickness material. Bracket comes with fasteners to install. Known as manufacturers part number H20559-BLK.

Aluminum Diamond Plate Kick Plate

Aluminum base material that has a polished chrome look with the diamond plate pattern. Diamonds are 1-1/8" long.
Custom sizes are available, they run about $0.39 per square inch

.125" thick

Please allow 7-10 days for delivery

B-273 Bobrick Toilet Tissue Dispenser for Single Roll. The unit is made of a cast aluminum satin finish with a plastic spindle that is theft resistant. Holds up to one roll 6" diameter. The unit measures 6-1/2"w x 4-7/8" projecting out from the wall. This also has a controlled delivery.

B-4262 Surface Mounted Towel Dispenser with TowelMate on sale today. Satin finish stainless steel. Paper dispenser holds 400 c fold or 525 multifold towels. Complete with tumble lock on top of cabinet and includes key, cabinet slots indicate refill time. The unit is 10-13/16" x 13-1/4"ht x 4-7/8" depth.

B-2890 Bobrick single jumbo toilet tissue dispenser. The unit is a satin finish stainless steel. Equipped with a keyed lock. The spindle holds up to one 10" diameter roll and for a 3" diameter core. Stainless steel mounting plate and is 10-21/32"w x 10-5/8"h x 4-1/2"depth.

B-2892 Bobrick double jumbo toilet tissue dispenser. The unit is a satin finish stainless steel. Equipped with a keyed lock. The spindle holds up to two 10" diameter roll and for a 3" diameter core. Stainless steel mounting plate and is 20-13/16"w x 11-3/8"h x 5-5/16" depth.

Partition Inswing Surface Keeper 1-1/2" Between Screws Cast Stainless Steel

Cast stainless steel construction. The keeper base is 2-1/2" tall by 1-3/32" wide. The latch face measures 2-1/2" tall with a 7/8" projection. The hole spacing is 1-1/2". The slot measures 5/16" by 1-9/16". Also known as a Bathroom Stall Keeper-Inswing Flat. Manufacture part # 5163.

Shipped with mounting screws.

Aluminum Kick Plate with Diamond Plate Finish, .063 inch thick.  Same as our 1/8 inch thick plate, but 1/16 inch thick. Plates come with or without screws, the without will not be drilled.

Truth 16.16 Sash Lock.

3" x 2-9/16" x 1", with 2-3/8" hole spacing

This sash lock has been discontinued. If you order this part, the 16.27 will be sent as a replacement. According to the factory, the Wi1627 will work as a replacement with any modification.

Used truth keeper # Wi20034

Outdoor 6' X 10' Flag.  Outdoor American 5' X 8' Flag. Rich, lustrous appearance with superb wearing strength and breath-catching beauty. 100% nylon material, originated for flags-durable fast colors, washable, won't shrink with sewn special thread. Sheds water, flies well, even in the rain. Polyester canvas headings with spur-type brass grommets or roped headings with galvanized metal thimbles.

Fiat Partitions Coat Hook Bumper

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Plastic end cap for all Adams Rite Concealed Vertical Rod and Mortise devices.

Plastic cap measures 2-3/8" high by 1-1/16" wide by 1-1/4" projection. The metal tab measures 1-3/16" wide by 5" long.

Adam Rite Part # 41-0901-05-IP

The GS780R Rubber Stair Tread is a Raised Disc.  It features an adjustable nose that drops down 1-9/16".  The nose is 1/8" thick.  You have two choices on the Grit Stripping, the Visual Impaired 1-2" wide or 2-3/4" wide grit tape strips. They are designed for interior use.

Adams Rite New Style end cap for the 8700 and 8800.
The black cap measures 2-3/8" high x 1-1/2" wide x 1-1/4" projection. We some times find the number 25-0674-01 cast in the black plastic.

Adams Rite Part # 41-0901-03-IP

Flush Metal Partitions Coat Hook Bumper

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Single prong locker hooks for coat rods and school type lockers. The hook is made from a metal 1/8" diameter tube x 4-3/4" ht x 2" width. These locker hooks are wall mounted to the locker back or sides. The hole spacing is 3/4", the top hole is 3/16" round with the one lower.& Also known as 8699.

Toilet Partition "U" Wall Bracket For 1-1/4" Thick Panel Stamped Stainless Steel

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 1-13/32" . Leg project out 1-1/2" with the thru hole at 1-1/8" from the base. The 4 thru holes are 1/4" diameter, two of them are the mounting holes. Also known as a Bathroom Stall U Wall Bracket. Manufacturer part # 1949.

Shipped with screws

Zamac die cast and polished chrome plate construction. Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5980

Shipped with screws for mounting.

Monarch 19 Series End Cap

Black plastic end cap measures 2-1/16" high by 1-5/8" wide with a 1-7/16" projection. Cap mounts on to the two mounting holes fo the End Cap Bracket which are about 9/16" on center.

Monarch Falcon Part # 650343 or old part # 6135

This system is perfect for hotels, restaurants, churches and schools. It is easy to install and built to last.

Note: Hangers not included.

Coat Rack Information
Height: 12" (305mm)
Length: 2' to 50'+
Projection: 12 7/8" (327mm)
Slat Color Options: Light Oak Medium Oak Walnut
Racks can be made any size up to 50'.

Manufacturer will use slip joints so the rack can ship UPS/FEDEX.

Dor-o-Matic 1490 RHR/1590 LHR Push Label
4-7/8" x 1-7/16"

Doromatic part # 4270107321 or PB212 Black-No longer available
Doromatic part # 4270107320 or PB214 Gold

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 3-15/16" with the mounting screws are 2-3/16" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and Two Wing Bracket. Manufacturer part # 1839.

Shipped with screws

Leveler Glide with Metal Swivel Base. 1/4-20 thread metal base swivel glide. Stops the wobble of an uneven floor. 1 1/4" base diameter and 1 1/8" stem length. Can also be used with a t-nut to install in wooden legs. Use a spring clip to install in hollow legs.