Search results for: 'cover latches tread tip acrylic spic togeth'

Monarch 19-V Series Chassis Assembly Cover

This is the cover for the Monarch Falcon 19-V Rim Device. The cover measures 5-7/8" tall by 2-1/2" wide with a projection of 1-7/8".

Monarch/Falcon part # 650385
Old Part # 6134

Piano Hinge W/Cover lh in/rh out 54" aluminum anodized is a heavy duty 1/4" pin with spring to close. this hinge has 5 holes on each side with 13" centers and starts at 1" from top and bottom. The cover makes the hinge holes not as noticeable. Also known as 8684.

Need extra brackets for your Secuity Latches, you can order them here.  The are sold individually.  Constructed of welded steel and this then powder coated black.

775 EPOXY FLOORING ADHESIVE

The only recommended adhesive for use with Disc-O-Tile. May be used with other rubber stair treads, tile and flooring. Because of flame spread properties, other adhesives will not bond Disc-O-Tile to the floor. A two-part solvent-free adhesive; contains 1 can Part A 1 can Part B, and a stirring paddle. Covers approximately 150 square feet per unit. Enviromental Friendly!

Adhesive information

• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustment

Less all parts means, only the Cylinder!

Bobrick B-4221 seat cover dispenser surface mounted in a satin finish stainless steel. Dispenses 250 single or half folded covers. Fills at the bottom. the unit is 15-3/4" w x 11" ht x 2" depth.

For installing Rubber Floor Tiles or Rolls over suitable on-grade dry concrete floors, suspended concrete floors, or suspended wood floors. May also be used with sanded back molded rubber stair treads. Not recommended where excessive moisture exists; Non-Carcinogenic; Non-Toxic; safe for the environment and freeze thaw stable. See label for complete instructions. Ready to trowel in 1 gallon or 4 gallon cans. Covers 150 square feet per gallon.

Adhesive information

ASI Matte Black toilet seat cover dispenser is surface mounted and can dispense 250 single or half-fold seat covers. Fabricated of 22 gauge type 304 stainless steel with satin finish. The product is stainless steel with a matte black powder coated finish. With a matte black finish this product offers a more sophisticated and bold look while being aesthetically appealing to the eye.

Dimensions

15-3/4” x 11” x 1-7/8” (400 x 279 x 48 mm)

Von Duprin Exit Device 88 Axle Package

Von Duprin 88 Axle Package

New style axle snaps together, and replaces the old style which were screwed together with allen wrenches. This style of axle has been around since about 1990. The piece on the right is only used for taking the axle apart.

Von Duprin Part # 090006 or 090082

Double Door Latch for doors without a center post. Shown with out lock. Optional lock is just to prevent theft.

Von Duprin 33/3547A Center Case Kit Less Cover

Replacement Von Duprin 33/3547A Concealed Vertical Rod Device Center Case.

Von Duprin Part # 050405

Von Duprin 33/35A Rim Center Case Kit Less Cover

Replacement Von Duprin 33/35A Rim Device Center Case.

Von Duprin Part # 050403

Black Rubber Feet with Metal Cap designed to be used on Brunswick Furniture. 

Center Hung Door Closer

• Available (NHO) non-hold open, or (SHO) selective
  hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
  latch and backcheck adjustments
• Built-in positive dead stop prevents door
  from swinging beyond desired opening
  degree
• Vertical and horizontal door adjustment
• Arm centering adjustment

Double Door Latch -- Rests firmly against the center post. Shown with optional lock. Lock prevents theft.

Recessed Mounted Seat Cover Dispenser Keyed, 18"x21"x3", Stainless Steel

The 8-32 screw set for the diamond shaped latches. This thread is special to the chrome or stainless steel diamond shape looking surfacemount latch. Note the screw length is 1-1/8" and is a one way screw, the female portion is included and is slotless head. This is for a 1" door.

B-2012 Bobrick automatic wall mounted soap dispenser in stainless steel with satin finish. Corrosion resistant valve dispenses a variety of liquid soaps and disinfectants. The valve is a sensor activated and does not require contact, just motion. The unit has lockable housing shall be equipped with a clear acrylic refill indicator window and is hinged for refilling. This unit holds 30 fluid ounces bulk fill.

Metal Door Automatic Flush Bolts FB31P

Fully automatic-inactive door is latched, bolts are extended when active door closes, door is unlatched, bolts retract when active door is opened. The Ives FB31P Body is 1” wide by 6-3/4” long and 2” deep. Bolt throw is 3/4” with a 7/8” adjustment with a 3/4” backset,  standard rod is 12” which is measured from the center of latch body to the bolt tip.

Rods are also available in 18”, 24” and 36”, call for pricing.  We ship the 12” rods, and this set would include the top and bottom latches.

3 Hour UL Listed

Ives Part # FB31P

Von Duprin 33/3527A Center Case Kit Less Cover

Replacement Von Duprin 33/3527A Surface Vertical Rod Device Center Case.

Von Duprin Part # 050404

Brackets designed to mount plexiglass/acrylic sheets to desk surface edge when creating separation/barrier. Brackets are adjustable for thickness from 1/8" to 3/8". It is recommended for use of 1/4" Thick material. Sold as a Pair. Made of Aluminum Alloy. Screws and inserts included. Uses a 5mm/3/16" Allen Key(Not Included) to install screws These are available in either Silver or Black Finish. Silver Finish are readily available while Black Finish may have an extended leadtime depending on quantities being ordered.

Measurements

Height: 2-1/2"

Width: 1-3/4"

Depth: 5/8"

Weight:About 1.3lb

Top to Bottom: 3-5/8"

Plate Width: 1-3/4"

Plate Length: 5-3/4"

Plate Height: 3/16"

Gap/Spacing: 1"

Flush Metal Slide Bolt Latch

Zamac die cast construction, polished chrome finish. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/16" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch. Manufacture part # 5020.

Shipped with mounting screws.

Corbin Russwin ED5200S Latch Assembly

The Corbin Russwin ED5200S 681F608 Latch Assembly is used on the Wider Stile SecureBolt Exit Device.  The difference between the ED5200S and ED4200S Latch Assembly is the location of the Hub.  Hub on the ED5200S Latch Assembly is located off the center line of the Assembly Mounting Screws.

Corbin Russwin Part # 681F608

The Hub Position for this Latch is the ED5200

Hadrian Partitions Slide Bolt Latch Chrome Plated

Zamac die cast construction, polished chrome finish. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/16" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch. Manufacture part # 5020.

Shipped with mounting screws.

Cal Royal 2000 Night Latch Trim

3" X 7-3/4"

Cal Royal Part # 2200NL

The Adams Rite EX76 End Caps are for the Concealed Vertical Rod Devices. The package includes the hinge side and latching side covers, along with the mounting screws. The aluminum color is no longer available, only Black.

Doromatic 1590 Latch Bolt Assembly

Replacement Latch Bolt Assembly for the Falcon Doromatic 1590.   In the old days you could just replace the PB355 (SPRING.127) spring, but as of November 2015 you have to replace the complete latch head assembly.

Doromatic Part # 4270107603

Brackets designed to mount plexiglass/acrylic sheets to desk surface edge when creating separation/barrier. Brackets are adjustable for thickness from 1/8" to 3/8". It is recommended for use of 1/4" Thick material. Sold as a Pair. Made of Aluminum Alloy. Screws and inserts included. Uses a 5mm/3/16" Allen Key(Not Included) to install screws These are available in either Silver or Black Finish. Silver Finish are readily available while Black Finish may have an extended leadtime depending on quantities being ordered.

Measurements

Height: 2-1/2"

Width: 1-3/4"

Depth: 5/8"

Weight:About .9lb

Top to Bottom: 3-5/8"

Plate Width: 1-3/4"

Plate Length: 3"

Plate Height: 3/16"

Gap/Spacing: 1"

The Burns 618 Locking Pocket Door Latch is 2-3/4 inches tall by 2-1/2 inches deep. The mortise dimensions are 2-5/16 inches tall by 1-7/8 inch deep. Base metal is Brass or Aluminum depending on the finish.

Yale 7100F Series Latch Assembly

This Yale Latch Assembly is used on fire rated panic devices. A fire rated panic is a device were you can not lock the latch in the open position. It is used on doors were the engineers want the door to latch every time it closes to contain a fire.

Yale Part # 60-7000-0425-048

Note the Hub Position of this latch is the 7100

American Seating Rubber feet for #60, 253 and 254 Folding chairs.

Ives Roller Latch RL1130

The Ives Roller Latch RL1130 is a combination of the RL30 and an Angle Stop.  Tension is easy to adjust with the two tension screws on the face plate.

Brackets designed to mount plexiglass/acrylic sheets to desk top or work surface when creating separation/barrier. Brackets are adjustable for thickness from 1/8" to 3/8". It is recommended for use of 1/4" Thick material. Sold as a Pair. Made of Aluminum Alloy. Screws and inserts included. Uses a 5mm/3/16" Allen Key(Not Included) to install screws These are available in either Silver or Black Finish. Silver Finish are readily available while Black Finish may have an extended leadtime depending on quantities being ordered.

Measurements

Height: 2-1/2"

Width:1-3/4"

Depth: 5/8"

Weight:About .6lb

Von Duprin 8827-F Special Hex Stud Kit

The Von Duprin Special Hex Stud mounts on the upper and lower latches.  The cover attaches to the Hex Stud, it is like a spacer.

Von Duprin Part # 050478
Old Part # 961218

Sico Rubber Folding Table Glide for use on 3/8" outside diameter locking leg. Sico part number 177.