Search results for: 'stop steel tops with 11 4 id coil'

8" Kickdown Door Holder / Stops Grand Standard

No roll pin at pivot point
Mallable with a pair of pliers
Rubber shoe held on by a screw
American Made
Zinc plated steel

Made by Grand Specialties 608z

Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.

12" Kickdown Door Holder / Stop Grand Standard

No roll pin at pivot point
Mallable with a pair of pliers
Rubber shoe held on by a screw
American Made
Zinc plated steel

Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.

Made by Grand Specialties 612z

Toilet Partition Continuous Toilet Partition Hinge 57-1/2" With Spring Close Stainless Steel
Lh Inswing or Rh Outswing See Diagram

16 gauge (.060" thick) stainless steel with 4 springs. 3" wide when laid flat x 57-1/2" long. 1/8" diameter hinge pin. Mounting screws are located every 11" or so. Can be raise up 3/8" for emergency entrance. Also known as a Bathroom Stall Piano Hinge, or Full Length Stainless Steel Continuous Piano Hinge. Manufacture part # 7669.

Shipped with all the fasteners

Interior Steel Equipment Locker Expanded Metal Lock bar for 36" double tier locker. Used in 1965 - 1994. Also known as 2636, is4016. This lock bar was used with a locker turn handle, the turn handle  connected to the lock bar creates the bars to retract or expanding locking at the top and bottom of the locker to lock it.

Ives Wall Mounted Door Holder WS40

• Constructed of sturdy cast brass, or aluminum.
• Holder is mounted on wall and strike is mounted on door.
• Roller on holder rides up seats itself on strike, with a heavy duty bumper
  pad deadening the sound and shock.
• Universal screw pack accommodates all types wall construction.

Base Height: 2"
Base Width: 2-1/2"
Base Projection: 2-1/4"
Engaged Projection: 3-1/2"
Strike Height: 2-1/16"
Strike Width: 3/4"
Strike Projection: 2"

Von Duprin 8827 Top Rod Connector

Inserts into rod so the latch can connect to the rod. The top vertical rod does not ship with the top rod connector!

Von Duprin Part # 050279
Old Part # 960577

Medart Bleacher Top Bar Only for front row truck assembly.

Angle Base 1-3/8" Window Handle-11/16" Drop

Cast white bronze with a brushed nickel finish

Flush Metal Partitions Top Hinge Escutcheon For 7/8" Thick Door

Chrome plated Zamac die casting. Top hinge insert outside dimensions are 2-3/8" by 1" wide by 1-5/8". Two of the three holes are 13/32" diameter and the third is 7/32". Also known as a Bathroom Stall Door Inser Top 7/8". Manufacture part # 1540.

Bobrick also used this insert.

Von Duprin 88 Spring Stop Assembly

This is the piece that holds the hinge case spring in place. It is used on all of the Von Durpin 88 models.

Von Duprin Part # 050451
Old Part #107682

Stamped SS One Ear Bracket 3/4" Panel 1-1/2" X 2-1/2"

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 2-5/32" with the mounting screws are 1-11/32" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and One Wing Bracket. Manufacturer part # 1649.

Shipped with screws

The Dorma RTS88 Top Arm 8835 is for use on Double or Single Acting doors that have a 1" top rail.  This is the standard arm on the RST07 and RST10 packages.

Dorma Part # 8835

Cal Royal 900 Series Door Closer

Pull or Push side, or Top Jamb mounting, Meduim Duty Door Closer, Powder Coated Painted Finishes, 5 year warranty

3/4" x 11-1/8" cylinder hole spacing

Cal Royal 900 Series Catalogue

Napkin Disposal w/o Shelf Stainless Steel Surface mount 16 gauge utility shelf. Overall Size 7 1/2" x 10" x 3 7/8".  Surface Mounted Sanitary Napkin Disposal shall have top cover door and cabinet of 22 gauge type 304 stainless steel alloy 18-8. All exposed surfaces shall be satin finish and be protected during shipment with PVC film easily removable after installation. Capacity shall be 1.2 gal (4.5L). Top cover is attached to cabinet with a full length 3/16" diameter (Ø4.8) stainless steel multi-staked piano hinge. Structural assembly of body and door components shall be of welded construction. American Specialties 0852 stainless steel napkin disposal unit.

Flush Metal Partitions Top Hinge Casting For Metal

Unplated Zamac die casting construction. The outside dimensions of the top hinge casting are 5-1/8" high by 2-5/8" deep by 25/32" wide. Two of the three holes are 3/8" diameter, and the other hole is threaded for a 5/16-18 screw. Also known as a Bathroom Stall Door Insert - Top 1". Manufacture part # 4556.

The Rixson 998 and 997 Magnet Assembly and Bracket is the replacement magnetic coil for the 998 and 997 Rixson Electro Magnetic Holders.

Rixson Part # 998369

Von Duprin 8827-F Top Latch Cover Kit - 050465

This is the Top Latch Cover for the Von Duprin 8827-F. The 8827-F is the Fire Rated Surface Vertical Rod device usually used on interior doors to contain a fire. The Fire Rated version would not have dog screws to lock the device in the retracted postion.

Von Durpin Part # 050465
Old Part # 961206

The 1 inch diameter Decorative Cap comes in two different tread sizes 1/4-20 and 5/16-18.  The Cap measures 1 inch diameter by 3/8 inch thick. Stainless Steel base material.

Cast Stainless Steel Bottom Hinge for 1-1/4" Sq Edge

Cast stainless steel construction. The hinge measures 2-1/4" high by 1-1/4" wide and the hole spacing is 1-1/2". The U channel is 2-1/4" by 1-1/4" by 1" deep. The lug projects out 1-5/8" by 1/2" thick with a 5/16" diameter bushing. Also known as a General Bathroom Stall Pivot Hinge Bottom 1-1/4". Manufacture part # 3293.

Shipped with mounting screws.

a=1-5/8"

This is a replacement for the Zamac Die Cast hinges for General, American Sanitary, Flush Metal and Fiat Partitions.

The 1-1/4 inch diameter Decorative Cap comes in two different tread sizes 3/8-24 and 5/16-18.  The Cap measures 1 inch diameter by 3/8 inch thick. Stainless Steel base material.

Penco Locker Top Cam assembly for double door lockers.

Fiat Partitions Top Door Insert For 1"

Chrome plated Zamac die cast construction. The hinge U insert has outside dimesions of 2-3/16" wide by 1-1/2" by 1" deep with tow holes 1/2" diameter. The inside distance between the U's is 1-1/16". Also known as a Fiat Bathroom Stall Door Insert Top 1". Manufacture part # 4800.

The Jackson 2085-3185 Top Strike Package is mounted on the frame of the door were the top latch can engage it.   The Package includes the Strike, Plate, Latch Adjusting Wrench and the Mounting Screws.   Jackson Part Number 30-1345.

Leveler Glide with Metal Swivel Base. 1/4-20 thread metal base swivel glide. Stops the wobble of an uneven floor. 1 1/4" base diameter and 1 1/8" stem length. Can also be used with a t-nut to install in wooden legs. Use a spring clip to install in hollow legs. 

Partition Top Hinge Casting

Unplated Zamac die cast construction. The outside dimensions of the top hinge casting are 3-7/16" high by 2-3/8" wide by 1-5/32" deep. The casting features four holes, two of them are 3/8" diameter, one is 7/32" diameter and the fourth is a threaded hole for a 5/16-18 screw. The two U channels have spacings of 13/16" and 1" on the other. Also known as a Bathroom Stall Door Insert - Top 1". Manufacture part # 4546. Used with AMPCO and Metpar Toilet Partitions.

Von Duprin 33/3547A/48A Adjustable Top Rod

Replacement Von Duprin 33/3547A/48A Adjustable Top Rod for 6'8" to 8'4" doors.

Von Duprin Part # 050519

Interior Steel Equipment Locker Expanded Metal Lock bar for 30" double tier locker. Used in 1965 - 1994. Also known as 2630, is4015. This lock bar was used with a locker turn handle, the turn handle  connected to the lock bar creates the bars to retract or expanding locking at the top and bottom of the locker to lock it.

Knickerbocker Partitions Bottom Hinge 1-1/4" Round Edge

Chrome plated Zamac die cast construction. The wrap around dimension is 1-1/4" wide by 1-3/4" high and 11-16" deep. The hole spacing is 1-1/8" on center. The lug projects out 1-3/8" to center hole with a 1/4" bushing diameter. Also known as a Bathroom Stall Pivot Hinge - Bottom 1-1/4". Manufacture part # 3420.

a=1-11/16"

Von Duprin Steel Mullion 4954 7'6"

The standard mullion used on most double doors with the Von Duprin Exit Devices.  We ship the 7'6" mullion, if you need the 8'6" or 10'6", please call.  Package includes the 050390 and 050335 top and bottom brackets.

Von Duprin 8827 Top Latch Case for non fire rated doors. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted postion.

Von Duprin part # 050460
Old Part # 101750

Von Duprin 98/9947 Adjustable Top Rod

Von Duprin 98/9947 Adjustable Top Rod for 6'8" to 8'4" doors.  This rod is used on the 9847, 9847-F, 9947 and 9947-F

Von Dupin Part # 050574
Old Part #110375