Search results for: 'guard 8 deep bolt door hiny'
-
International Door Closer 9001 Series
International Door Closer 9001 Series
1. ADA (Handicap) multi-sized closer with adjustable spring power
2. Adjustable spring power 1 through 6 (adjustable after installation)
3. Precision cast aluminum housing with forged steel arm
4. Stable hydraulic door check fluid for any climate operation. Using a fire resistant oil with an
operating range from -43.6°F (-42°C) to 140°F (60°C)
5. Standard sweep and latch speed
6. Standard adjustable backcheck or without backcheck
7. Two speed control valves allow closing and latching speeds to be controlled by separate
valves; fully adjustable after installation
8. Standard Tri-packed for regular arm, top jamb and parallel arm application
9. Numerous accessories are available to allow for special installations or adaptability
10. Finishes available in Aluminum (AL) and Duronodic (DU)3/4" X 11-3/32" Hole Spacing
9001P- -
Doromatic SC70 Door Closer
Doromatic SC70 Door Closer - Same Hole Spacing as the Norton 7500 and Yale 4400
2-3/8" x 6-3/4" hole spacingANSI/BHMA A156.4, Grade 1
■ UL Listed
■ ADA compliant
■ 1-1/2” diameter piston
■ Hinge side, top jamb and parallel arm configuration standard with SC71 Rw/PA
■ Adjustable size 1-6
■ Single piece cast aluminum body
■ Staked valves
■ Separate adjustable general speed, latch speed, backcheck and backcheck position
■ Non-handed for left and right swinging doors
■ 10 year warrantyWe ship the SC71 Rw/PA
SC70- -
Cal Royal 900 Series Door Closer
Cal Royal 900 Series Door Closer
Pull or Push side, or Top Jamb mounting, Meduim Duty Door Closer, Powder Coated Painted Finishes, 5 year warranty
3/4" x 11-1/8" cylinder hole spacing
900P- -
Ampco Bottom Cam Housing Chrome Plated
Ampco Partitions Bottom Cam Housing Chrome Plated
Chrome plated Zamac die cast construction. The housings outside dimensions are 3-1/8" wide by 1-5/32" deep by 1-7/16" high. The screw hole is 7/32" diameter. The square slot is 1" by 15/16". The square bulge were the screw is located is 1-1/2" by 1-5/32". Also known as a Bathroom Stall Door Insert - Bottom 1". Manufacture part # 4060
91005BC. -
Concealed Latch Cast SS Keeper Bumper Inswing 1-1/4"
Concealed Latch Keeper Bumper Inswing For 1-1/4" Square Edge Post Cast Stainless Steel
Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5983
Shipped with screws for mounting.
9A5983 -
Chrome Plated Bumper Keeper 1-1/4" Round Edge
Chrome Plated Toilet Partitions Bumper Keeper For 1-1/4" Round Edge
Polished chrome plated Zamac construction. The strike and keeper measures 2-1/2" tall by 1-7/8" wide. The mounting holes are 1-1/2" on center. The stop measures 3/4" wide by 17/32" deep with a rubber insert bumper. Slot is 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1-1/4". Manufacture part # 5430.
Shipped with mounting screws.
9A5430 -
Yale 4400 Door Closer
Yale 4400 Door Closer
- Non-handed
- Rack-and-pinion design
- Cast aluminum body
- 2-1/8" (54mm) projection
- 1-1/2" (38mm) diameter piston
- 5/8" (16mm) diameter pinion journals
- Staked valves
- Standard, separate and independent, latch, sweep and
backcheck intensity valves - Backcheck positioning valve
- NorGlide® fluid
- Molded plastic cover
- All standard arm applications allow doors to swing 180°,
conditions permitting - Self-drilling screws
- Full-size template
- 10-year limited warranty
2-3/8" x 6-3/4" hole spacing. This door closer replaces the 4400BF. This newer version is Barrier Free Compliant.
4400- -
Penco Locker Door Frame Assembly
Penco Products door frame assembly are the whole front face of the lockers. Includes door, frame and all latching with handle choice. This takes 6-8 weeks delivery. These doors are standard louvered known as the vanguard lockers. These lockers are typically in the hallways of schools.
pencod/f -
Floor Mounted Door Holder/Stop FS43
Ives Floor Mounted Door Holder FS43
Features:
• Automatic door holders ideal for heavy-traffic situations that require a simple,
fool-proof, Hold-Open device.
• Forged from brass.
• Unit is activated automatically when door is opened. A firm pull on door releases
the mechanism.
• Strikes accommodate different door to floor clearances.
• Model numbers are determined by strike/door-to-floor clearances.
• Holder position on door is adjustable.Door to Floor Clearance 1-5/8" to 2-11/16"
Holder Dimensions 3" Wide x 3-11/16" HighGJF43A- -
Concealed Latch Cast SS Keeper Bumper For 1-1/2" screws
Concealed Partition Latch Keeper Bumper For 1-1/2" Between Screws Cast Stainless Steel
Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-13/16" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. The slot is for the concealed latch is 7/8" high by 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5243
Shipped with mounting screws.
9A5243 -
Yale 50 Series Door Closer
Yale 50 Series Door Closer
- ANSI A156.4, Grade 1
- 10-year warranty
- Non-handed
- Rack-and-pinion design
- Cast aluminum body
- 1-3/8" (35mm) diameter piston
- 5/8" (16mm) diameter pinion journals
- Standard, separate and independent, latch, sweep
and backcheck intensity valves - 2-7/8" (73mm) projection
- Tri-Packed- packed for regular arm, top jamb and
parallel arm installations. - All standard arm applications allow
Older models may be stamped with Scoville or Eaton, which are the companies that used to own Norton
We some times find 20-0054-4001 or 20-0254-4001 stamped on the back of the closer50- -
Concealed Latch Cast SS Keeper Bumper Inswing
Concealed Partition Latch Keeper Bumper Inswing Cast Stainless Steel
Stainless steel casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5653.
Shipped with mounting screws.
9A5653 -
Keeper Bumper For Throw Latch Inswing Flat Stop
Chrome Plated Partition Keeper Bumper For Throw Latch Inswing Flat Stop
Chrome plated Zamac die casting. The strike and keeper measure 2-1/2" tall by 2-9/16" deep and is 1/8" thick. The stop projects out 3/4" and has a rubber insert. The mounting holes are 1-1/2" on center. Slots are 1/4" deep by 13/16" high. Also known as a Bathroom Stall Strike and Keeper - Inswing Flat. Flat backed for wall mounting. Manufacture part # 5280
Shipped with mounting screws.
9A5985 -
Sanymetal Keeper 2 Between Screws
Sanymetal Partition Keeper 2" Between Screws Inswing Flat
Polished chrome plated Zamac construction. Keeper base is 3" high by 1-1/16" wide with a 2" hole spacing. Strike is 3" tall by 7/8" deep. The material 1/8" thick. The slot is 1-1/8" high by 1/4". Also known as a Bathroom Stall Keeper Inswing Flat. Manufacture part # 5130.Shipped with mounting screws.
9S2401 -
Ives Roller Latch RL32
Ives Roller Latch RL32
The Ives Roller Latch RL32 is constructed of Brass and Plated to your desired finish. The body measures 1-1/8" wide by 2-1/4" high and 2-1/4" deep. The roller is constructed of Nylon, and has an adjustable projection up to 1/2". Fits a standard heavy-duty cylindrical lock cutout.
RL32- -
Kickdown Door Stop / Holder For FS1154, FS544, and FS555
Rubber Shoe For GJ1154M and GJL444-555 Kickdown Door Stop / Holder
Replacement rubber shoe
5/8" insert diameter
1" base diameter
8-32 threaded screwGJ1154 -
Fiat Bottom Door Insert
Fiat Partitions Bottom Door Insert For 1" Doors
Chrome plated Zamac die cast construction. The bottom door insert measures 2-1/8" by 1" by 13/16". The insert has one hole, which is 7/32" diameter. The square hole is 29/32" wide by 1". Also known as a Fiat Bathroom Stall Door Insert Bottom 1". Manufacture part # 4700.
9F0317 -
Keeper Bumper Inswing 1-1/4"
Zamac die cast and polished chrome plate construction. Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5980
Shipped with screws for mounting.
9A5980 -
Door Silencer For Metal Doors
For use on metal frames featuring
pneumatic design that, once installed,
forms an air pocket to absorb sound and
reduce noise of door closing.Diameter: 1/2"
Thickness: 1/8"
GJ64 -
Cal Royal 400 Series Door Closer
Cal Royal 400 Series Door Closer
Adjustable closing and latcting speeds
Powder Coated Painted Finishes
5 year warrantySize 420 3/4" x 6-5/8" hole spacing
Size SM 430P 3/4" x 6-1/2" hole spacing
Size 430P 3/4" x 8-3/16" hole spacing
Size 440P 3/4" x 8-3/16" hole spacing400P -
Stamped SS Door Pull 5" Between Screws
Partition Door Pull 5" Between Screws Stamped Stainless Steel
Stamped stainless steel construction, 3/32" thick. The door pull measures 5-21/32" wide by 5/8" high by 1-11/16" projection with a 5" on center hole spacing. Also known as a Bathroom Stall Door Pull. Manufacture part # 6419.
Shipped with mounting screws.
9A6419 -
Ives Roller Latch RL30
Ives Roller Latch RL30
The Ives Roller Latch RL30 is constructed of Forged Brass and Plated to your finish. Furnished with a Nylon Roller. Body measures 1" wide by 3-3/8" high by 1-11/16" deep. The roller has a maximum projection of 3/8" and is easily adjustable.
RL30- -
Detex ECL-230X Alarmed Deadbolt Panic Hardware-Single Point
The Detex ECL-230X Panic Device is a single point deadbolt device. One size fits 36 to 48 inch doors. The dead bolt has a 1 inch throw and is saw resistant. Locking and unlocking dead bolt always arms and disarms alarm. The alarm is 100 decibels and is powered by a 9 volt battery. Email for more information.
ECL-230