Nylon Glide Caps-1-7/32". Fits over table and chair glides that have an outside diameter of 1-7/32".  Made of a natural white nylon, that will not color or scratch floors.

Non Skid Glide Cap Protective Chair Tip

This Glide Cap has a non skid rubberized bottom to prevent you chairs from sliding, while at the same time providing protection for your floor. This cap will fit on all of our Metal and Nylon Based Swivel Glides.

This Glide Cap is designed for use with our SGR Glides, or Swivel Glides Round 1-1/4" bases.

Nylon Glide Caps-1-3/16". Fits over table and chair glides that have an outside diameter of 1-3/16".  Made of a natural white nylon, that will not color or scratch floors. Reduce noice from chairs moving and keep your floors from being scratched. 

Floor Saver Glide Cap Protective Chair Tip

This Glide Cap has a raised ring on bottom to prevent your chairs from scratching your floors, while at the same time extending the life of your current glides. The raised ring will push the dirt that is on the floor away so it will not scratch the floor. This cap will fit on all of our Metal and Nylon Based Swivel Glides.

This Glide Cap is designed for use with our SGR Glides, or Swivel Glides Round 1-1/4" bases.

Nylon Glide Caps-1-1/16". Fits over table and chair glides that have an outside diameter of 1-1/16".  Made of a natural white nylon, that will not color or scratch floors. Protect your floors from scratching with this Nylon Glide Cap. 

Smooth Bottom Glide Cap Protective Chair Tip

This Glide Cap has a smooth bottom to prevent your chairs from scratching your floors, while at the same time extending the life of your current glides. This cap will fit on all of our Metal and Nylon Based Swivel Glides.

This Glide Cap is designed for use with our SGR Glides, or Swivel Glides Round 1-1/4" bases.

Nylon Glide Caps-1-1/4". Fits over table and chair glides that have an outside diameter of 1-1/4".  Made of a natural white nylon, that will not color or scratch floors.

Felt Based Glide Cap Protective Chair Tip

This Glide Cap has a felt based bottom to prevent your chairs from scratching your floors, while at the same time extending the life of your current glides. This cap will fit on all of our Metal and Nylon Based Swivel Glides.

This Glide Cap is designed for use with our SGR Glides, or Swivel Glides Round 1-1/4" bases.

Swivel Glide Puller to speed the removal of old glides. This Glide remover provides a firm grip to remove your glides. Place the forked end on the glide and use a mallet to remove your old glide. Most commonly used to remove old school glides. 

Krueger Swivel Glide for 5/8" Inside Diameter and 3/4" Outside Diameter Tubing

Plastic swivel glide for use on Krueger Chairs and Desks.

Krueger Swivel Glide for 7/16" Inside Diameter and 5/8" Outside Diameter Metal Tubing Leg

This plastic swivel glide is not longer made, but you can use the SGR62AN or SGR62I as a replacement. The SGR62AN will work, but not if you are stacking your chairs. The SGR62I ( the last letter is I, as in Island) is the one you want to use if you stack your chairs for storage. See the "Related Products" on the right hand margin of the page.

Adjustable Height Swivel Glide, Nickel Based for chair legs with a 5/8" outer diameter and a 1/2" inside diameter. The base of this glide is 1 1/4" in diameter. This glide helps level uneven chairs. 

3 Prong 7/8" Slide For Wood Furniture

7/8" base diameter. Metal base slide for wood furniture. You should use a diameter that aproximately half the diameter of furniture leg.

Leveler Glide with a Nylon Swivel Base. Glide is 5/16-18 thread, with a 1 3/4" base diameter and 1 1/2" stem length. Stop wobbling of uneven floors with this Metal Furniture Foot.   Screw into a thread leg hole to reach your desired height. Combine with a tnut to install in wooden furniture legs. 

1/4-20 thread Leveler swivel nylon base glide. Stop wobbling of uneven floors with this Metal Furniture Foot.  1 1/8" base diameter and 1 1/8" stem length. Screw into a thread leg hole to reach your desired height. Combine with a tnut to install in wooden furniture legs. 

3 Prong 5/8" Slide For Wood Furniture

5/8" base diameter. Metal base slide for wood furniture. You should use a diameter that aproximately half the diameter of furniture leg.

Leveler Glide with Metal Swivel Base. 1/4-20 thread metal base swivel glide. Stops the wobble of an uneven floor. 1 1/4" base diameter and 1 1/8" stem length. Can also be used with a t-nut to install in wooden legs. Use a spring clip to install in hollow legs. 

Square Chair Turing Metal Swivel Glide with a Square Tubing measurement of 7/8" O.D. X 3/4" I.D. This metal swivel glide has a 1 1/6" base diameter and also has a ferrule. 

7/8" diameter Nylon based Nail On furniture glide. Protect hardwood, ceramic tile, linoleum & hard surfaces from mars & scratches by using this nail on glide.

Square Leg Metal Swivel Glide with a 1-1/16" base diameter. This Chair Glide does not have ferrule. This swivel glide is for a square tubing chair leg with a 7/8" outer diameter and a 3/4" innner diameter. 

Swivel Glide Square tubing Leg with a  13/16" O.D. X 11/16" I.D. The base on this chair glide is 15/16" in diameter. This swivel based chair glide features a ferrule. 

Metal Swivel Glide for a Square Leg with a square tubing 13/16" O.D. X 11/16" I.D. The base on this swivel glide is 1 1/16" in diameter. This glide does not feature a ferrule. 

Chair Glide for a square leg chair with tubing outer diameter 3/4" and inner diameter of 5/8". 1 1/16" Base diameter. This glide does not have a ferrule.  

7/8" Nail On Glide-Nickel Base

Nail on furniture glide, 7/8" diameter metal base

Sled Base Metal Glide and Rivet

Used on American Seating Chairs
7/8" diameter metal base

Irwin Glide With Metal Cap

for 1/2" outside diameter tubing

product includes metal base and nickel plated tubing collar

Swivel Glide for a Square tubing Leg  chair with a 1" O.D. X 7/8" I.D. 1 1/16" base diameter. This glide does not have a ferrule. 

3/4" Nail On Glide Felt Bottom

This nylon glide is ideal for replacing the metal caps on wooden chairs when they are on hardwood floors or tile.   Simply remove the old metal cap with a screw driver and nail on the 3/4" outside diameter felt bottom glide.

Safeglides-Brown 1" Base Diameter Nail On Glide for furniture. To install the glide, tap it into your wooden furniture.

Safeglides-Brown 1 1/2" Base Diameter Nail On Glide for furniture. To install the glide, tap it into your wooden furniture.

Metal Chair Swivel Glide for a chair with round tubing with measurements of 1/2" O.D. X 11/16" I.D. With Ferrule. Used on American Desk Chairs and various other manufacturers, fits 1/2" inside diameter, and 11/16" outside diameter tubing. 1 1/4" metal base. 

1/4-20 Threaded Leveler with a Felt Base to be screwed into a 1/4" threaded hole in furniture leg. You can also combine with a t-nut to use in wooden furniture. Base Diameter and Stem Length are 1" on this glide. 

Metal based glide that nails into wooden furniture, 1 1/8" diameter base glide. .

Heavy Duty Non-Swivel Leveler for chairs and tables.   Has a thread of 5/16-18, base diameter of 1 3/4" and a stem length of 1 1/2". This heavy duty glide screws into a threaded hole in the leg or table to selected height. Use with a Tnut to install on a wooden leg.