Search results for: 'guard 8 done bond door hold'

Corner Guard CG-10 3" x 3"

90 degree 3” x 3” vinyl corner guard with aluminum retainer.  Vinyl flex action absorbs impact, and is .100” thick, the aluminum retainer is .062 thick.  Available in 4, 8 and 9 foot lengths.  Top and bottom end caps included with the corner guard.

Corner Guard CG-20 2" x 2"

90 degree 2” x 2” vinyl corner guard with aluminum retainer.  Vinyl flex action absorbs impact, and is .085” thick, the aluminum retainer is .062 thick.  Each corner guard includes the end caps.  Available in 4, 8 and 9 foot lengths.  Corner guards are shipped with a top and bottom end cap.

VINYL BACK COCOA MAT ROAD ROLLERS

Road roller mats are made with fibers from the almost indestructible outer husk of the coconut. These fibers are bonded into a vinyl backing. These vinyl back Road Roller Mats can be installed much easier than woven mats and can be easily cut to fit without the mat unraveling. If small holes are needed for installation, a sharp knife or punch will easily do the job.

Rollers are 32' 9" long and around 1-3/16" thick

Use adhesive where Grit Strip is applied to porous surfaces such as wood or concrete. Grit Strip adhesive is recommended as a sealer; will give a better, longer lasting bond. Recommended application temperature is 60 degrees and above. One quart covers approximately 50 square feet (single coat) of Grit Strip; available in quart and pint units.

Adhesive information

FLUFF-CORD STRIP TILE

A close-nap carpet-like surface of specially processed rubber-fabric strips made from recycled heavy-duty truck and bus tires; Natural Earthtone Gray Color. Strips are heat bonded to a woven flexible backing. This creates a "dry-back" adhesive back that reacts with our non-flammable adhesive to form a stronger bond to the floor. Install this permanent entry floor mat inside or outside; cord strips act as a wiper where dirt or moisture is a problem; are non-skid, non-absorbing, resist shrinkage, deaden sound. Ideal for heavy wear areas in shopping centers, lobbies, entryways, ramps, airports, etc. Produced in standard 12" x 12" tile size.

Tile must be installed using manufacturer's specific installation instructions and Musson No. TT-390 Non-Flammable Environmentally Safe Adhesive.

Order Fluff-Cord Strip Tiles here

775 EPOXY FLOORING ADHESIVE

The only recommended adhesive for use with Disc-O-Tile. May be used with other rubber stair treads, tile and flooring. Because of flame spread properties, other adhesives will not bond Disc-O-Tile to the floor. A two-part solvent-free adhesive; contains 1 can Part A 1 can Part B, and a stirring paddle. Covers approximately 150 square feet per unit. Enviromental Friendly!

Adhesive information

FLUFF-CORD STRIP TILE-CONTINUOUS STRIP

A close-nap carpet-like surface of specially processed rubber-fabric strips made from recycled heavy-duty truck and bus tires; Natural Earthtone Gray Color. Strips are heat bonded to a woven flexible backing. This creates a "dry-back" adhesive back that reacts with our non-flammable adhesive to form a stronger bond to the floor. Install this permanent entry floor mat inside or outside; cord strips act as a wiper where dirt or moisture is a problem; are non-skid, non-absorbing, resist shrinkage, deaden sound. Ideal for heavy wear areas in shopping centers, lobbies, entryways, ramps, airports, etc. Produced in longitudinal rolls 12" wide x 25' long.

Tile must be installed using manufacturer's specific installation instructions and Musson No. TT-390 Non-Flammable Environmentally Safe Adhesive.

Order Fluff-Cord Strip Rolls here

For bonding to all Disc-O-Treds, Rubber Stair Treads or Koroseal Vinyl Stair Treads to concrete, pan filled, wood, metal, marble and terrazzo steps. A rapid drying, long range contact cement; specially formulated for Musson stair coverings. Brush on application; use on back of treads and back of nosing. Contains solvents, extremely flammable. 1 gallon covers 75 lineal feet of stair treads (brush on back of tread and step). Ready to use in 1 quart, 1 gallon and 5 gallon containers.

If ordering the gallon or 4 gallon pail, it will ship via freight truck. If you would prefer something that ships Fed Ex Ground, please order the 300 Stair Tread Adhesive.

Adhesive information

GSA11 ALUMINUM STAIR TREADS

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 11" model here.

SPECTRA RIB CARPET MAT-OLEFIN

Ribs that scrape, valleys that hold dirt and moisture. Ribbed carpet surface wipes shoes better, saves on clean up time of your floors. Shaded carpet effect brightens your entryway.

Available in Stock Sizes or Custom Lengths 24", 36" or 48" wide.

See more views box for colors.

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 9" model here.

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 7-1/2" model here.

DR-CT DIAGONAL RIB CARPET TILES
An attractive and functional entrance matting alternative; heavy duty modular carpet tile with excellent scraping and dirt removal properties for high traffic areas. Designed for interior use in entrances, vestibules, lobbies, between double doors, on ramps or in elevators.

Install in a recess or on the surface. Our easy release adhesive allows you to remove worn or damaged tile which is easily re-adhered. Tile can be switched to decrease traffic patterns; lasts longer, looks better. Vinyl or Aluminum beveled edging available.

3/8" thick; 19-11/16" x 19-11/16" square tile; diagonal rib pattern woven of 100% polypropylene pile yarn with a bitumen backing.

SPECIFICATIONS--No. DR-CT

DR-CT Diagonal Rib Carpet Tiles made of 100% polypropylene pile yarn with a bitumen backing in areas as indicated on drawings. Tile shall be of first quality commercial grade carpet, free of surface defects. Install tile in an alternating rib parquet pattern in indicated recess with recommended easy release adhesive, (or on surface area using vinyl edging or aluminum beveled frame). Tile shall be 3/8" thick, 19-11/16" x 19-11/16" square carpet tile. Select from standard carpet colors of Cranberry, Blue, Beige, Teal, Gray, Chocolate or Charcoal.

one DR-CT Diagonal Rib Carpet Tile covers 2.69 square feet

Interlocking 1/2" x 11-7/8” x 11-7/8” recycled PVC tiles with bristle carpet inserts. Brushes off sand, dirt and slush from shoes and cart wheels; open grid drains away water and debris. Modular 11-7/8” x 11-7/8” tiles allow flexibility and the ability to fit the product to any size area. Tiles snap together easily to install and replace. Beveled ramp edges are available for non-recessed applications.

This product is part of our sustainable development program where the tiles can be returned at the end of the lifecycle for a credit toward replacement product. The material is then cleaned, ground, treated for contaminants in an environmentally safe process, and re-formed into new matting. Check with our customer service department for details.

Sold in cartons of 24 tiles, 23.36 sq feet

Improve safety and prevent worn carpet edges on steps; for new or renovation work. Butt 1/4” to 3/8” thick carpet against both the top and bottom lips of butt-type carpet nosing. Standard 8’ lengths; easily cut to size. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.140 Koroseal Vinyl Ribbed Carpet Nosing; 3-1/8” deep; 2-1/2” nose depth; square adjusta-nose. Lap 5/16”, 1/4" or 3/8” carpet over lip on both the step and riser. Select from standard colors of black, brown.

Shipping:   Due to shipping costs, this product is shipped in two 48" sections

Ribbed Koroseal Vinyl lap-type nosing for front edge of stages, bowling lane steps, platform-like floors and bar foot rests. Form fitting adjusta-nose; has a 7/8” lip to allow 1/8” flooring to lap over back edge. Standard 8’ lengths. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.105 Service Weight Koroseal Vinyl Ribbed Lap-Type Nosing; 2-3/4” deep; 1-1/2” nose depth; square adjusta-nose. Lap 1/8” flooring over the back lip to butt against ribbed design. Select from standard colors of black or brown.

Shipping:   Due to shipping costs, this product is shipped in two 48" sections

Description

SPECIFICATIONS:

• Koroseal vinyl rib design stair treads
• Thickness: 1/8"
• Depth: 9-5/8"
• Snap on nose
• Sizes available: 18", 24", 30", 36", 42", 48" or 72"
• Colors available: Brown, Black

The 522 Rubber Landing tiles measure 19-11/16" x 19-11/16" and are 1/8" thick

Size 19-11/16" x 19-11/16" (50cm x 50cm)
Overall Thickness:  1/8" 9/64" w/ profile
Profile Height:   1/32"

Ribbed Koroseal Vinyl butt-type nosing for front edge of stages, bowling lane steps, platform-like floors and bar foot rests. Grooved cutting guides provide “cut-offs” to match flooring thickness. Standard 8’ lengths; easily cut to size. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.101 Heavy Duty Koroseal Vinyl Ribbed Butt-Type Nosing; 3-1/2” deep; 1-5/16” nose depth; square adjusta-nose. Cut nosing at proper guide to butt against 1/8” (or 3/16” or 1/4”) flooring. Select from standard colors of black or brown.

Shipping - Due to shipping restrictions, this product ships in two 48" long pieces.

The 882 Low Profile Landing Tile is designed for use with the 820R Stair Treads.   The tiles measure 19-11/16" x 19-11/16".

Size:  19-11/16" x 19-11/16"
Overall Thickness:  1/8"

The 780R Rubber Stair Tread is a Raised Disc.  It features an adjustable nose that drops down 1-9/16".  The nose is 1/8" thick. They are designed for interior use.

405CR Vinyl Stair Tread Risers

Plain color cove risers match Koroseal vinyl stair treads; or use a contrasting riser with vinyl or rubber treads; easily trimmed in height and length; savings in installation are substantial; cove risers are same sizes as stair treads.

SPECIFICATIONS:

Furnish and install No 405CR Koroseal vinyl coved stair riser; 1/8” thick, 7” high with 5/8” toe; ribbed back. Select standard length of 18”, 24”, 30”, 36”, 42”, 48”, 54”, 60”, 72”, 84” or 96”. Select standard solid color of Brown, Sand, Gray or Black.

The 620D Rubber Stair Tread comes in two versions, Square Nose and Round Nose. This page is for the Round Nose, Search 620DSN for the Square Nose Version. This tread offers an 1/8" nose thickness, with a 3/4" radius. They are designed for interior use.

The 1010R Rubber Stair Tread features a Rib Design, with grooves all along the fall line.   The round nose is not tapered or adjustable.  The nose is 1/8" thick and tapers to 3/32" at the very back.  The radius of the nose is 3/4". They are designed for interior use.

The 520S Rubber Stair Tread has a 1/4" nose thickness which tapers down to 1/8" at the back.  The nose drops down 1-9/16", and the nose is not adjustable and is not tapered. They are designed for interior use.

The 605CR Rubber Coved Riser goes in the back of the step and acts as a kick plate in the matching color of your stair treads.  The Riser is 7" tall and features a 5/8" cove to aid in cleaning of the back of the step.

The 620D Rubber Stair Tread comes in two versions, Square Nose and Round Nose.  This page is for the Square Nose, Search 620DRN for the Round Nose Version.   This tread offers an 1/8" nose thickness, has an adjustable and tapered nose. They are designed for interior use.

The GS780R Rubber Stair Tread is a Raised Disc.  It features an adjustable nose that drops down 1-9/16".  The nose is 1/8" thick.  You have two choices on the Grit Stripping, the Visual Impaired 1-2" wide or 2-3/4" wide grit tape strips. They are designed for interior use.

BERBER TILES BT-220 ENTRANCE MAT

A heavy-duty, 40-oz./sq. yard needlepunch olefin tile that "breathes" so that moisture evaporates quickly. This 3/8" x 19-11/16" x 19-11/16" tile with a bitumen backing will not shrink or curl. The berber texture offers all the advantages of a heavy-duty wiper/ scraper with a custom carpet look.

Sold in cartons only of 12 tiles, enough to cover 32.3 square feet

See Color Chart under "More Views"

The 7520R is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Round Nose, for Square Nose search 7520R. The treads are 1/8" thick along the entire depth of the treads, and have a nose that drops down 1-9/16".  The 7520R Round Nose is not available with the Grit Stripping. They are designed for interior use.

The 1010R Rubber Stair Tread features a Rib Design, with grooves all along the fall line.   The sqaure nose is not tapered or adjustable.  The nose is 1/8" thick and tapers to 3/32" at the very back. They are designed for interior use.

The 820R is a low profile raised disc design for lighter traffic.  The tread is 3/16" thick at the nose and tapers to 1/8" at the back.  The nose has a 1-9/16" length.  These treads are easily trimed in the field with a straight edge and utility knife. The nose is not adjustable and is not tapered. They are designed for interior use.

The GS520S Rubber Stair Tread with grit stripping has a 1/4" nose thickness which tapers down to 1/8" at the back.  The nose drops down 1-9/16", and the nose is not adjustable and is not tapered. You have two choices on the Grit Stripping, the Visual Impaired 1-2" wide or 2-3/4" wide grit tape strips. They are designed for interior use.

The GS820R is a low profile raised disc design for lighter traffic.  The tread is 3/16" thick at the nose and tapers to 1/8" at the back.  The nose has a 1-9/16" length.  You have two choices on the Grit Stripping, the Visual Impaired 1-2" wide or 2-3/4" wide grit tape strips.  These treads are easily trimed in the field with a straight edge and utility knife. The nose is not adjustable and is not tapered. They are designed for interior use.