Search results for: 'space lead high privacy'

Truth Awning Operator Guide Bar Clip

This plastic clip was used to hold the older version Guide Bar or Track. The piece measures 3/4" wide, by 5/8" high, with an 11/16" projection. The clip is made of plastic.

Part # Wi39947

Two Hole 1-1/2" Window Handle

This handle is the same as the T1015, but with a 1-1/2" hole spacing and a 9/32". The handle is constructed cast white bronze with a brushed nickel finish.

Right Hand Shown in Picture

LCN SEM7820 Magnetic Door Holder

Chrome Plated Toilet Partition Flat Stop Keeper

Polished chrome plated Zamac construction. The keeper base is 2-1/2" tall by 1-3/32" wide. The latch face measures 2-1/2" tall with a 7/8" projection. The hole spacing is 1-1/2". The slot measures 5/16" by 1-9/16". Also known as a Bathroom Stall Keeper-Inswing Flat. Manufacture part # 5160.

Shipped with mounting screws.

Concealed Partition Latch Keeper Bumper 1-1/4" Post Round Edge Cast Stainless Steel

Cast stainless steel construction. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5513.

Shipped with mounting screws.

7/16" X 3/4" SLOT

The 4310HSA SENTRONIC is an electrically controlled closer/holder designed to provide easy passage for groups of pedestrians through high traffic doors. Pedestrians, moving through the doorway, trigger the built-in scanner. When the door is opened to 80° or more, the door is electrically held open to minimize wear and tear on applied door hardware. After the last pedestrian in a group passes through the doorway, the system timer releases the hold-open, closing the door under control of the heavy duty closer. Single lever (track) arm closer is specifically designed for pull side mounting. Choice of finishes and accessories meet virtually all high traffic installation requirements.

The 4410HSA SENTRONIC® is an electrically controlled closer/holder designed to provide easy passage for groups of pedestrians through high traffic doors. Pedestrians, moving through the doorway, trigger the built-in scanner. When the door is opened to 80° or more, the door is electrically held open to minimize wear and tear on applied door hardware. After the last pedestrian in a group passes through the doorway, the system timer releases the hold-open, closing the door under control of the heavy duty closer. Double lever arm closer is specifically designed for push side mounting. Choice of finishes and accessories meet virtually all high traffic installation requirements.

The Partition Double Door Pull 5-1/2" stainless steel come as two handles for mounting back to back handles on an one inch thick door.  The handles have 5-7/8" center to center hole spacing, and the screws included are for a 1" thick door. This is constructed of cast brushed stainless steel. The manufacturer part number on this part is 900112. Overall width is 6-3/4"

Toilet Partition two ear pilaster bracket kit for 1-1/4" thick material. This brackets base is 1-1/2″ wide x 4″ long with 3″ center to center hole spacing and comes out from the wall 2-1/2". The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. Brackets are Included with security screws for installation. Also known as 615220.

Engraved Push Plate-Stainless Steel

16 gauge (.050") brushed stainless steel push plate with black engraved 3/4" high  "PUSH".  Available in two sizes 3-1/2" x 15" and 4" x 16".   Only available in Brushed Stainless Steel.

Project In Window Handles-1-1/2"

This window handle has a hole spacing of 1-1/2" with a 7/16" lock up. It is also known as a Off-Set Project In Window Handle because the point of rotation does not line up with the screws holes, it is off-set. Cast white bronze with a brushed nickel finish

Chrome Plated Slide Bolt Latch 1-1/2" Wide X 3-1/4" High, 2-3/4" Between Screws. Die cast construction and polished chrome plated. Used on Accurate Toilet Partition and Global Toilet Partitions. Also known as a Surface Mounted Bathroom Stall Slide Latch and Toilet Partition Locks. Known as 40-8512899. Shipped with mounting screws. This latch is Ada approved.

Tip- Proof Flag Stand - 1". Cast stand with universal bore. Supplied with adapter sleeves to accommodate various pole diameters. This is an indoor flag stand. The flag base is 10-3/4" diameter and 5-1/2" high. This flag stand weighs 9 pounds. 

Metpar Pintle For Laminate 1/2" Diameter

White nylon and steel construction. The pintle is 1/2" diameter by 2-5/16" high. The threads are 5/16-18. Also known as a Bathroom Stall Pintle. Manufacture part # 98265.

Shipped with lock washers and nut.

Toilet partition round edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1-1/4" thick by 3" high. This size pilaster post shoes are split on one end for easy installation. Also known as a Bathroom Stall Pilaster Post Shoe Round Edge. Used for the base of the support system with pilaster mounting.

LCN SEM7830 Magnetic Door Holder

Comtec Toilet Partition Aluminum 6" Outswing Strike And Keeper For 1" Post Or Pilaster

Clear Anodized aluminum construction. Strike and Keeper is 6" high by 1-15/16" wide. The three mounting screws are 2" on center apart. Also known as a Bathroom Stall Strike and Keeper outswing1". Used mostly on Solid Plastic (HDPE) Toilet Parttions. Known as 5878.

Shipped with mounting screws.

Zipper Pile Weatherstrip .270" Backing - .200" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

Zipper Pile Weatherstrip .270" Backing - .250" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

Roto Casement Operator

This Roto Casement Operator features a hole spacing of 3-1/2" on thee outside mouting holes and 1-7/8" on the two inside mouting holes.  The housing is contructed of die case metal that is electro-statically painted.   The housing is 5-1/2" wide.  The optional handle fits the 5/16" Hex Shaft.

Left Hand Shown in picture

International Door Closer 3020-VO Arm and Track

International Door Closer 3020-VO Arm and Track for Offset Top Arm Assembly Mortised Type (7/8" Depth of Top Rail). Track measures 12-5/8" long by 1/2" high by 1-1/4" wide.

Project In Handle With Ring Pull -1-3/8" hole spacing with a 7/16" lock-up C Dimension

Cast white bronze with a brushed nickel finish

Partition Inswing Surface Keeper 1-1/2" Between Screws Cast Stainless Steel

Cast stainless steel construction. The keeper base is 2-1/2" tall by 1-3/32" wide. The latch face measures 2-1/2" tall with a 7/8" projection. The hole spacing is 1-1/2". The slot measures 5/16" by 1-9/16". Also known as a Bathroom Stall Keeper-Inswing Flat. Manufacture part # 5163.

Shipped with mounting screws.

Toilet partition continuous aluminum door stop for 1" panel outswing doors. This product is clear anodized aluminum. This full length door stop with block the gap between the door and the post next to it. For an outswing the latch locks on the back side of the bumper. The door keeper and strike is 54" in length and has 5 holes spaced at 13" apart and starts at 1" from the top and the bottom. Also known as 134314 strike & keeper channel. Includes all hardware.

Sanymetal Coat Hook Bumper 3" Projection

Chrome plated Zamac die cast construction. The coat hook base measures 2" by 1-11/16" with a 1-1/8" hole spacing. The hook projects out 1-13/16". The bumper projects out 3" with a rubber insert on the tip. Also known as a Bathroom Stall Hook. Manufacture part # 4280.

Shipped with mounting screws.

Ives RL32 Nylon Roller RLPART.1045

This replacement Nylon Roller and Rivet Package is for the Ives RL32 Roller Latches.  The Roller measures 3/4" high by 5/8" diameter.  The Rivet measures 15/16" long and is threaded on one side.

Ives Part # RLPART.1045

Door Pull 12

This handle has a 5-1/2" centers hole spacing and is 6" overall. It has 2" projection with 1-3/8" clearance and the base is 5/8" x 1-1/4". Also known as a Door Handle or Door Grip. Shipped with thru bolts and finish washers.

Finishes

Truth 16.16 Sash Lock.

3" x 2-9/16" x 1", with 2-3/8" hole spacing

This sash lock has been discontinued. If you order this part, the 16.27 will be sent as a replacement. According to the factory, the Wi1627 will work as a replacement with any modification.

Used truth keeper # Wi20034

Global Partitions Bottom Hinge For Surface Mount. Chrome plated Zamac die cast construction. Used with powder coated steel and stainless steel partition doors. Pivot hinge is 2-3/16" tall by 1-1/2" wide. The hole spacing is 1-1/2" on center. The lug projects out 1-9/16" and is 1/2" thick. The bushing on the lug is 5/16" diameter. Manufacture part # 3010, 111710. Also used with Flush Metal and General Partitions. Shipped with mounting screws. A=1-9/16". Also used with Accurate Partition doors after January 2013.

Indoor Flag Stand - 1 3/8". These cast stands are designed to compliment any flag set. Easily movable, these are the most practical stands for general use. This flag pole base is 12" diameter and 6" high. This flag stand weighs 15 pounds. 

International Door Closer 3010-JO Arm and Track

International Door Closer 3010-JO Arm and Track for Offset Top Arm Assembly Mortised Type (9/16" Depth of Top Rail). Track measures 15-1/4" long by 3/4" high by 15/16" wide.

The Aluminum Bleacher End Cap is also known as Part #P7002N.

Note: We offer 7½" (P7002na), 9½" (P7002nb), and 11½" (P7002nc) width for Aluminum Bleacher End Caps. They are 1¾" thick and feature 2 bends of 1⅛" & ⁹⁄₁₆". The Aluminum Bleacher End Cap includes self taping screws. Please select the appropriate size from the dropdown menu below.

This aesthetically-pleasing Aluminum Bleacher End Cap is designed to provide a clean and finished look to your aluminum bleacher system. Made from high-quality materials, these Aluminum Bleacher Ends ensure longevity and resistance to wear and tear, making them an ideal choice for schools, sports facilities, and outdoor events.

The Aluminum Bleacher End Cap is easy to install, fitting securely onto the ends of your bleacher rows. Its sleek design not only enhances the overall appearance of your seating but also helps to prevent debris from entering the bleacher structure, maintaining a tidy environment.
Whether you're upgrading existing bleachers or installing new ones, the P7002N End Cap is a reliable solution that combines functionality with aesthetic appeal.

Consider implementing a cleaning and maintenance schedule to keep your bleachers looking their best. A clean and well-maintained environment not only enhances the aesthetic appeal but also contributes to the longevity of the materials. Simple tasks like wiping down surfaces and removing debris from the Aluminum Bleacher End Caps can make a significant difference. Whether it's comfort, accessibility, or safety concerns, replacing worn-out Aluminum Bleacher End Caps with new ones can help you prepare for future upgrades or changes involving your bleacher systems. By prioritizing maintenance, safety, and user experience by installing new Aluminum Bleacher Ends, you can ensure that your bleacher system remains a dependable and welcoming space for all events.

Please feel free to contact us for assistance with ordering the correct replacement Aluminum Bleacher End Caps for your specific needs. We are always glad to help you choose the best options for your bleacher systems. Order yours today!

Ordering Online All Stainless Steel Floor Mounted Urinal Screens Manufactured by Global Partitions. All toilet partitions ship in 48-72 hours plus 2-4 days travel. All chrome plated hardware included. Stainless Steel Floor Anchored 70" high pilaster and 58" high panel. Specify - Part # 9SFASS-XX (where XX is width from the front of the pilaster to the wall). Width of panels 16"-76" and panel height is 58".

Global Stainless Steel Color Chart

Top Partition Hinge For 1-1/4" Round Edge Post Or Pilaster

Chrome plated Zamac die cast construction. The outside dimensions of the hinge are 1-1/4" deep by 2-1/2" high by 1-7/16" wide. The U mounting channel is 2-1/8" high by 1-1/4" deep with a slot depth of 11/16". The mounting holes are 1-1/2" apart on center. The lug projects out 1-3/32" by 13/32" thick with a 3/8" diameter bushing. Also know as a Bathroom Stall Pivot Hinge - Top 1-1/4". Manufacture part # 4530. Used on Ampco and Metpar Metal Partitions.

Shipped with mounting screws.

A=1-7/16"

Plastic end cap for all Adams Rite Concealed Vertical Rod and Mortise devices.

Plastic cap measures 2-3/8" high by 1-1/16" wide by 1-1/4" projection. The metal tab measures 1-3/16" wide by 5" long.

Adam Rite Part # 41-0901-05-IP

Tip- Proof Flag Stand - 1 1/4". Cast stand with universal bore. Supplied with adapter sleeves to accommodate various pole diameters. Indoor Flag Stand use only. This flagstand is 10-3/4" diameter and 5-1/2" high. The flag base weighs 9 pounds.