Search results for: 'grey 8 door braced door horn'
-
Plastic Chair Tips Square Tubing 1-1/4 inch O.D. X 1-1/8 inch I.D.
Plastic Chair Tips for Square Tubing Chair Legs. This tip is For a 1-1/4" Outside Diameter X 1-1/8" Inside Diameter Chair Leg. Available in Black.
PS125 -
Norton 7700 Power Track Hook-Up Boxes
Norton 7700/7705PT Hook-Up Boxes come in two voltages, 24 and 120, and two configurations Hinge Side and Stop Side. Hinge Side means the track is on the side of the door that you can see the Hinges, also know as the pull side. Stop Side means the track is on the push side of the door.
PTOHB- -
Cast SS One Ear Bracket For 7/8" Panel, 1-1/2" X 2-1/2"
Toilet Partition One Ear Wall Bracket For 7/8" Panel Cast Stainless Steel
Cast stainless steel construction. Base of the bracket is 2" x 1-1/2", with 1-1/8" hole spacing. Bracket legs project out 2-1/2" with the screws at 2-1/8" on center from the base. The four holes are 1/4" diameter. Also known as a Bathroom Stall One Ear Wall Bracket or One Ear 7/8". Manufacture part # 1653.
Shipped with mounting screws.
9A1653 -
Stainless Steel Continuous Hinge,57"-14 Gauge,1/4" Pin
Toilet Partition Continuous Hinge, 57" Long Non Handed,14 Gauge Stainless Steel ,1/4" Diameter Pin, Cam Close. The hinges must be mounted flat when door is shut. For inside swing the hinges are mounted on the inside of the stall. For the outside they must be mounted on the outside.
This is the most Heavy Duty Continuous Full Length Hinge we sell. 14 gauge (.075" thick) stainless steel construction with a 1/4" diameter hinge pin. The hinge leafs are angle cut so your door will close with the camming action. The hinge is 3" wide when laid flat, and 57" long. Screws are spaced 11" apart and the holes are 9/32" diameter and has 6 sets of holes. Hinge can be raised up 3/8" for emergency entry. Also known as a Bathroom Toilet Stall Full Length Continuous Hinge. Manufacturer part #7789, 160029, 650-9400.
9A7789 -
Metpar Keeper Bumper Inswing
Metpar Toilet Partitions Keeper Bumper For 1-1/4" Inswing Square Edge Pilaster Or Post
Zamac die casting that is polished chrome plated. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4". Manufacture part # 5110
Shipped with mounting screws.
9CP250 -
Baby Changing Table SS Recessed Horizontal
The baby changing tables are a horizontal station, has a door facing and collar made from 18 gauge 304 stainless steel. Fabricated of FDA approved fungus and bacteria-resistant plastic. Unit complies with 2010 ADA Accessibility Standards and supports a static load of 300 lbs. This unit is used for recess mounting , also know as part number 9018 with American Specialties.
Dimensions
Closed:
39-5⁄32" x 28-1/4" x 3⁄8"
Open:
39-5/32" x 28-1/4" x 18-1/8"
Wall Opening:
35-1/2" x 24-1/2" x 4" min
9A9018 -
-
Stamped SS One Ear Bracket 7/8" Panel 1-1/2" X 2-1/2"
Toilet Partition One Ear Bracket For 7/8" Panel Stamped Stainless Steel
14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 2-5/16" with the mounting screws are 1-13/32" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and One Wing Bracket. Manufacturer part # 1659.
Shipped with screws
9A1659 -
Accurate Top and Bottom Hinge
Accurate Partitions Top and Bottom Hinge for 1-1/4" Round Post
chrome plated
used on Accurate Metal Partitions for mounting on a 1-1/4" thick round edge pilaster.
Accurate part number 50-8517300 and 50-2517200 and 50-398660. Security screws included.
A= 1-1/2", Used prior to January 1st 2013. There is no exact replacement hinge that will work.
**Not Available anymore, see link for new doors
9HAH15 -
Extra Long U Bracket 1" X 1-3/8" X 2-1/2"
If your toilet partition or bathroom stall wall bracket is cast with the number 1920 on the back, then you have the “U” Wall Bracket for 1″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1-1/4″ wide x 1-3/8″ tall, with the through hole located at 2-1/8″ from the back. If features 2 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall X Long “U” Bracket, or X Long “U” Wall Bracket.
9A1920 -
-
Plastic Chair Tip Round Tubing 1-1/2 inch O.D. x 1-3/8 inch I.D.
Black Round Plastic Chair Tips for Round Tubing Chair Legs with a 1-1/2" Outside Diameter X 1-3/8" Inside Diameter.
PR150 -
General Keeper Bumper For 1-1/4" Outswing Sq Edge
General Toilet Partitions Keeper Bumper For 1-1/4" Outswing Square Edge Pilaster Or Post
Zamac die casting that is polished chrome plated. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for outswinging doors. Also known as a Bathroom Stall Strike and Keeper-Outswing 1-1/4". Manufacture part # 5210
Shipped with mounting screws.
92060E -
Accurate Keeper Bumper for Inswing
Zamac die casting that is polished chrome plated. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4" Square Edge. Manufacture part # 5110. Shipped with mounting screws.
9HAP27 -
Napkin / Tampon Dispenser : Surface Mount
Napkin / Tampon Dispenser Surface Mount
Fabricated of Type 304 #18 Gauge Stainless Steel With #4 Satin Finish
Holds 30 Sanitary Napkin and 27 Tampon Packages
Multiple Coinage Options AvailableDoor
Fabricated of type 304 #18 ga stainless steel with #4 satin finish. Door has 1/2" returns for rigidity.
Body: Fabricated of type 304 #22 ga stainless steel with a #4 satin finish. Adj. Slip Flange: Fabricated of type 304 #22 ga stainless steel, one piece construction with no miters or welds and #4 satin finish. Flange will adjust from a 1" minimum to a 6" maximum wall depth.Coin Mechanisms: Two independent, trouble free turn knob mechanisms, with an "EMPTY" indicator that does not allow coins to be inserted into mechanism when product has been depleted. Operational with one hand with less than 5 lbs (22.2n) of force without tight grasping. Can be operated with palm, elbow or forearm if user has a physical impairment. (Free,.25,.50)
9AU527 -
Plastic Chair Tips Square Tubing 7/8 inch O.D. X 3/4 inch I.D. Rocker Type
Plastic Chair Tips for Square Tubing chair legs with a 7/8" Outside Diameter X 3/4" Inside Diameter Legs. This tip is a rocker type tip for slanted square legs and available in black.
KPSR87 -
Swivel Glide Square Leg 7/8 inch O.D. X 3/4 inch I.D.
Square Leg Metal Swivel Glide with a 1-1/16" base diameter. This Chair Glide does not have ferrule. This swivel glide is for a square tubing chair leg with a 7/8" outer diameter and a 3/4" innner diameter.
SGS87 -
Falcon-Doromatic 1690 Exit Device
The design of the Doromatic 1690 is ideal for demanding, high-traffic applications. The vertical rods and latch mechanisms are concealed in the vertical door stile, ensuring trouble-free operation. Cast metal cover plates and end caps hold up to rigorous use. A quick, singlepoint dogging feature in the housing deactivates the device, permitting unrestricted traffic flow. The Doromatic 1690 may also be used to retrofit a Doromatic 1990 Series crossbar device.
Replacement parts are also available
Shipped with all screws and strikes. The 1690NL Cylinder Assembly (169CA) is required if you wish to use a key cylinder on the exterior, SEE RELATED PRODUCTS toward the bottom of this page.
1690EO -
Plastic Chair Tips Square Tubing 3/4 inch O.D. X 5/8 inch I.D. Rocker Type
Square Plastic Chair Tips Square Tubing Chair Legs with a 3/4" Outside Diameter X 5/8" Inside Diameter Legs. This tip is a rocker type tip for slanted square legs and available in black only.
KPSR75 -
ASI locker Recess Handle for Single Point Latching
ASI locker Recessed Handle for Single Point Latching on lockers with no moving parts. The recess handle is Ada approved and is the new standard for lockers. When the door shuts closed there is a slot for the padlock eye to go through the recess handle for a padlock or built in lock to keep the door closed. This locker handle is made of stainless steel and very common to the locker industry.905001 -
Non Swivel Glide 1 inch O.D. X 7/8 inch I.D. Nickel Base
Non swivel glides for round tubing
1" outside diameter
7/8" inside diameter
1-1/16" base diameter
Nickel plated metal baseNSR100
