Search results for: 'brooke changing seating parts'

3/8" Spline Window Operator T Handle.

Converts existing crank handle to a compact T handle. Also known as a Butterfly Handle

Project In Window Handle 1-3/8"

This window handle has a hole spacing of 1-3/8" with a 7/16" lock up C Dimension. The handle is constructed of cast white bronze with a brushed nickel finish.

This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.

The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.

The rim device is non-handed.
A power supply is required for operation, see related products.
Ships with all the mounting screws and the 299 Strike.

Window Spring Latch

This spring latch features 1-3/8" hole spacing. They are used on older transom windows. White Bronze casting, nickel plated and then brushed

Two Hole 1-1/2" Window Handle

This handle features a 1-1/2" hole spacing with a 5/16" lock up. The handle is made of cast white bronze construction, with brushed nickel finish.

Right Hand Shown

Window Keeper-1-3/8" Hole Spacing

1-3/8" Hole spacing x 13/32" wide x 11/32" lock up

Cast White Bronze construction and nickel plated

Window Keeper 1-1/2" Hole Spacing

1-1/2" Hole spacing x 1/2" wide x 11/16" lock up

Cast White Bronze construction and nickel plated

Two Hole 1-3/8" Window Handle

This window handle features a 1-3/8" hole spacing with a 1/4" lock up. The window handle is constructed of a die cast material that is then powder coated.

Casement Window Handle Keeper Double Side

2-5/16" hole spacing x 5/8" wide

Stamped aluminum construction

Angle Base 1-3/8" Window Handle

1-3/8" center to center hole spacing with 8-32 threaded holes

Cast white bronze construction with brushed nickel plated finish

Project In Window Handles-1-1/2"

This window handle has a hole spacing of 1-1/2" with a 7/16" lock up. It is also known as a Off-Set Project In Window Handle because the point of rotation does not line up with the screws holes, it is off-set. Cast white bronze with a brushed nickel finish

Two Hole 1-1/2" Window Handle

This window handle has a 1-1/2" hole spacing with a 5/16" lock up dimension. The handle also features a ring pull for elevated windows. Cast white bronze with a brushed nickel finish.

Right Hand Shown

The Interkal Bleacher Wired Accupower Motor 1/4 Hp - 1 Phase is also known as K01151A100 or Part # P210709

Delivery of the Interkal Bleacher Wired Accupower Motor 1/4 Hp - 1 Phase we try to keep in stock at our facility for quick deliveries. The Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is designed specifically for use in Interkal brand bleacher systems (Vectra bleachers), providing reliable power and performance. With a horsepower of 1/4, it is ideal for applications that require moderate lifting and lowering capabilities. The single-phase design ensures compatibility with standard electrical systems, making installation straightforward.

The Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is built to last, featuring durable materials that can withstand the rigors of frequent use. Whether you are upgrading an existing bleacher system or replacing a worn-out motor, the Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is a solid choice. For those looking to enhance their bleacher operations, the Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase offers smooth and efficient performance with 115 volts. With its robust design and user-friendly features, this motor not only simplifies the operation of your bleacher system, but also ensures safety and durability.

To maximize the benefits of your Wired Accupower Motor 1/4 Horsepower 1 Phase for Interkal bleachers (Vectra bleachers), regular maintenance is recommended. This includes checking connections, lubricating moving parts, and ensuring that the motor is free from debris. By taking these simple steps, you can extend the life of your Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase and maintain optimal performance.

If you have any questions about the installation process or compatibility with your current setup, feel free to reach out to our customer service team. We are here to help ensure that you get the most out of your Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase. If you ever need assistance, our dedicated support team is just a phone call or email away. We are committed to providing you with the best service possible, ensuring that your Wired Accupower Motor 1/4 Horsepower 1 Phase for Interkal bleachers systems operates smoothly and efficiently for years to come. The Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is an excellent investment for anyone looking to enhance their seating arrangements. With its combination of reliability, efficiency, and ease of use, the Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is sure to meet your needs and exceed your expectations.

Window Spring Latch

Transom window spring loaded window catch. White bronze casting, brushed nickel finish. This Window Spring Catch features a 1-7/16" hole spacing, and a 1/2" lock up dimension.

5/16" Spline Window Operator Handle.

The Roto Notched Out SS Connecting Arm with Bracket is used with older Roto Operators.  Arm measures 5-3/8" long and the die cast bracket measures 2-1/8" long.

Two Hole 1-3/8" Window Handle 5/16" Lockup With Ring Pull

This window handle features a 1-3/8" hole spacing, a 5/16" lock up dimension and a ring pull for elevated windows. This handle is cast white bronze construction with a brushed nickel finish.

Right Hand Shown

Roto Split Arm Operator

The housing is 4-1/2" wide, and the linkage arm has an overall length of 4-3/8"

Right Hand shown in the picture

Zipper Pile Weatherstrip .270" Backing - .200" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

Zipper Pile Weatherstrip .270" Backing - .250" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

Two Hole 1-1/4" Window Handle 5/16" Lockup With Ring Pull

This window handle features a 1-1/4" hole spacing, a 5/16" lock up dimension and a ring pull for elevated windows. This handle is cast white bronze construction with a brushed nickel finish

Magnet Door Stop

Hands-free magnetic door stop/holder. All you need to do is open the door and a strong maget will keep it open until you close it. Mounts horizontally or vertically. Includes fasteners plus 1 concrete and 3 hollow wall anchors.

Not for use on doors with spring hinges or door closers.

Two Hole 1-1/2" Window Handle

This handle is the same as the T1015, but with a 1-1/2" hole spacing and a 9/32". The handle is constructed cast white bronze with a brushed nickel finish.

Right Hand Shown in Picture

A.W. Anderberg 77AL 4 Bar Window HInge, Aluminum Construction

29/32" track wide x 11/16" stack height

Found in commercial aluminum framed hopper windows.

10", 12" and 14" only, if you have an older larger size, please use the A.W. Anderberg 301ST or A.W. Anderberg 301SS as a replacement. You might have to shim the tracks in these cases, because the stack height is lower on the steel and stainless steel hinges. A.W. Anderberg no longer makes the larger sizes of the Aluminum Hinges due to the brittle nature of aluminum.

Sold Individually, these hinges are non-handed. We recommend that you change both hinges when replacing.

6-20-2012 No longer manufactured, what we have in stock, is what we have. You will have to replace with 301ST or 301SS Hinges

Casement Window Operator 9" Arm

Replacement Casement Window Operator is made of a die cast housing and steel arm. The window operator housing has 4 mounting holes, 4-3/4" are the outside dimensions of the outside screws and 3-7/8" on the inside screws.

Right Hand Operator Shown in picture

Clear Plastic Door Kick Plate

.125 inch thickness

Clear Acrylic

Custom sizes width x height x .22 = Cost $

Two Hole 1-1/4" Wedgeless Cam Handle

Hinged flap rolls down and locks the window shut. We find this window handle is used alot in the western states. The older version had a 1-3/8" hole spacing, but the new one has 1-1/4" hole spacing.

Sometimes we find the number R1 and CAN on this handle

White only!

Two Hole 1-1/2" Wedgeless Cam Handle

Hinged flap rolls down and locks the window shut. We find this window handle is used alot in the western states. The older version had a 1-3/8" hole spacing, but the new one has 1-1/2" hole spacing.

Sometimes we find the number R and 1 on the flap and DISCO cast in on the back of the handle. 

White only!

Two Hole 1-3/8" Window Handle 5/16 Lock Up

This window handle features a 1-3/8" hole spacing wth a 5/16" lock up. The handle as a cast white bronze construction with a brushed nickel finish

Project In Window Handle 1-1/2"

This window handle has a 1-1/2" hole spacing with a C Dim 7/16" lock dimension. The handle is constructed of a white bronze casting that is then brushed nickel plated.

Handless Window Lock 1-3/8"

This handle has a cast white bronze with a brushed nickel finish construction with a 1-3/8" center to center screw spacing. The handle has a 9/32" lockup, or distance between the base plane and the under side of the tongue. 1/8" allen screw will lock the handle so it can not be opened. This handle is ideal for schools, hospitals, and any other institution that is trying to lower heating and cooling costs by keeping the windows shut.

Project In Handle With Ring Pull 1-1/2"

This window handle has a 1-1/2" hole spacing with a C Dim 7/16" lock dimension. The handle is constructed of a white bronze casting that is then brushed nickel plated.

Aluminum Picnic Tables 6' and 8' available. The Aluminum picnic table has aluminum seats, aluminum table tops and steel legs. These sturdy maintenance free tables will provide years of service and are light weight. Our Aluminum Picnic table is an all anodized aluminum, maintenance free table that is light weight and will last for years and years.

Call for Pricing************

Two Hole 1-3/8" Window Handle 9/32" Lockup Most Popular

This window handle is constructed of cast white bronze with a brushed nickel finish. The handle has a 1-3/8" hole spacing with 9/32" lock up dimension. This window handle is one of our most popular.

Right Hand shown in Picture

Project In Handle With Ring Pull -1-3/8" hole spacing with a 7/16" lock-up C Dimension

Cast white bronze with a brushed nickel finish

The 2½" Aluminum Bleacher Clip is also known as Part #P2041U.

The 2½" Aluminum Bleacher Clips feature grooves 2-1/8" for the outer groove and 1" apart are the inner grooves. This clip replaces the 2-1/8" smaller version clip. You would use the outer and inner groove to make 1-3/4" between grooves. The 2½" Aluminum Bleacher Clip package includes a bolt and nut which are zinc cadmium plated.

Make your bleachers safe and secure with the reputable 2½" Aluminum Bleacher Clips. The durable 2½" Aluminum Bleacher Clips are designed to securely fasten bleacher seats to the supporting structure, ensuring safety and stability for spectators. Installation involves a quick setup and adjustments as needed. Each 2½" Aluminum Bleacher Clip is engineered to withstand heavy use, providing peace of mind during events. Made from high-quality aluminum, 2½" Aluminum Bleacher Clips hold up against rust and corrosion, making them ideal for both indoor and outdoor use. Whether you are managing a sports facility, school auditorium, or community center, the Aluminum Bleacher Clips 2½" are an essential component for maintaining the integrity of your bleacher system.

In addition to regular inspections, it is important to stay educated about the proper use and maintenance of the bleachers with information and/or training to help ensure that all staff understands how to operate the bleachers safely and effectively. Encourage your team to report immediately any replacements needed—whether it's loose 2½" Aluminum Bleacher Clips or damaged boards—so that repairs can be made promptly. We recommend keeping a maintenance log to track inspections and repairs for your bleachers. This can help you stay organized and ensure that nothing is overlooked. Regular maintenance not only enhances safety but also improves the overall appearance of your bleachers, making them more inviting for spectators.

For more information on specifications of the Aluminum Bleacher Clips 2½", please feel free to contact our customer service team. We can help you choose the best replacement part for your bleachers, whether it be the 2½" Aluminum Bleacher Clip or another product.