Search results for: 'locker number tabl 1 3 hold stop'

Nylon Glide Caps-1-1/16". Fits over table and chair glides that have an outside diameter of 1-1/16".  Made of a natural white nylon, that will not color or scratch floors. Protect your floors from scratching with this Nylon Glide Cap. 

Republic Steel Locker Screw 8-32 X 1/2" 8-32 X 1/2"

The LCN Fusible Link melts at 165 degrees to release the hold open mechanism.   Link measures 1-3/8 long by a 1/2" wide, the center to center distance on the holes is 15/16".

LCN Part Numbers:
4010-28
4110-30
4020-31

The 1-1/8" Q-Ball Floor Protector is for use on 1-1/8" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic.

Lyon Metal Locker Handle Lift for Left handed lockers, facing the locker if the hinges are on the Left side then they are a Left handed locker. November 1965- September 1981. Also known as 40108, 6756, ly2299, ll1765. Hole spacing for the lift is 1-3/4". 

Partition Strike And Keeper For 3/4" Door, 1-7/8" Between Screws Stamped Stainless Steel

Stamped stainless steel .075" thick construction. The strike and keeper measure 2-7/8" high by 2" wide with a 1-7/8" hole spacing. The stop posts are 5/8" wide by 7/8" tall with rubber inserts. For use with 3/4" square edge posts. Also known as a Bathroom Stall Strike and Keeper Outswing 3/4". Manufacture part # 6379.

Shipped with mounting screws.

Norton and Yale Hold Open Loop Assembly

This part is the part that always breaks on the Norton and Yale Friction Hold Open Arms. Cast Iron Construction, powder coated to the desired color.

Norton Part # 7701-13
Old Norton Part # 1620-13
Yale Part # 400-13

Chrome Plated "U" Bracket 1" X 1-1/2" X 1-3/8" . If your toilet partition or bathroom stall wall bracket is cast with the number 1910 on the back, then you have the “U” Wall Bracket for 1″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1-1/4″ wide x 1-3/8″ tall, with the through hole located at 1″ from the back. If features 4 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall “U” Bracket, or “U” Wall Bracket.

Door Stop / Holder Rubber Shoe

Replacement rubber shoe
1/2" insert diameter
1" base diameter
1" height

Black Rubber Feet with Metal Cap designed to be used on Brunswick Furniture. 

International Door Closer 522 Hold Open Arm

This is the New Style Hold Open Arm from International Door Closer. In July of 2014, the old style was discontinued. Look under "More Views" to see the Old Style. Shown in Dark Bronze, ships with all components in the picture.

International part # 522

The Swivel Glide 5/8" Outside Diameter with Ferrule Outside Holding Clip is used on American Desk, Artco Bell, Carter Craft, Krueger, Peabody and Virco Chairs. Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the out side of the leg, see more views for picture of outside holding clip.  This product will git all 5/8" outside diameter tubing.  The base has an 1-1/4".

Lyon Metal Locker double tier lock bar, 27-1/2" in length. Used Feb 1980 - Sept 1981.
2 Wire Springs included. Also known as 6776.

Hold Open Cushion Arm for the CRL PR90, Cal-Royal CR441 and International 44CI door closers.  For use in parallel arm applications only, T Handle locks the door in the open position.

Angle Base 1-3/8" Window Handle Truth

Also known as the Truth 25.39, this handle is constructed of a die cast metal and powder coated to the desired color. The distance between the screws is 1-3/8" on center. The handle measures 3-3/4" long, base measures 2-1/8" long. The number found on the handle is 45086 for the Right Hand, and 45085 for the Left Hand. We also find U.S. Pat. # 4,930,820

Right Hand is shown in picture.

Lyon Metal Locker Rubber Bumper (3/8" X 1/2"). June 2006 - Current. Also known as 6785 or 6803.

The Republic Storage #8 locker handle was made from 1936 to 1959. This locker handle was the only locker handle Republic Storage used in that time period. However, back them they were called Berger, then Republic-Berger, then Republic Steel, now they go by Republic Storage. The locker handle is 5-3/8″ long and 1/2″ wide. The screw holes are 3-3/4″ on center. Only 500 or less in stock, special order for more than. The handle is made of a die casting that is then chrome plated. The screws to attached the handle to the locker bar are included with the handle.

Republic Steel Locker Double Prong Wall Hook, hole spacing 5/8" on centers and are 3/16" diameter material used. The hook projects out 1-7/8".

Floor Mounted Door Stop and Holder
Manual type door holder ideal for interioror exterior use
Cast Bronze Construction
Strike features hinged hook which engages the holder
Accommodates door undercut up to 2-1/2"

The Swivel Glide 5/8" O.D. with Ferrule Outside Holding Clip Nylon Base is used on American Desk, Artco Bell, Carter Craft, Krueger, Peabody and Virco Chairs. Nylon or Plastic Base Glides slide easily across floors as long as the floor is free of grit and grime.  When you do have grit or grime on the floor, it gets impregnated in the nylon and will scratch the floor.  The top freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs and holds on to the outside of the leg, see more views for picture of outside holding clip.  This glide is designed for 5/8" outside diameter legs, and the base is 1-1/4" in diameter.

Chrome Plated Two Ear Urinal Bracket For 1" X 1-1/2" X 3-1/2

This bracket is usually used on Urinal Screens, which are the walls between men's urinals, to hold the partitions to the wall. The bracket is made of a zamac casting that is then chrome plated. The bracket base measures 1-1/2" x 4", with a 3" center to center hole spacing. The bracket projects out 3-1/2", with the mounting holes at 2-1/8" and 3-1/8" from the base. The holes used to mount the bracket to the wall and to the urinal are 1/4" diameter. The 1280 Bracket is sometimes called a Bathroom Stall Bracket, Toilet Partition Bracket, Two Wing Bracket, or Urinal Screen Bracket.

For 1" thick panels

The 524T has 1-1/4 inch diameter by 2-1/2 inches tall. It is constructed of brass and then powder coated flat black or brushed chrome plated. This stop ships with a lead anchor, 12-24 x 1 inch machine screw, #12 x 1-1/2 inch SMS with plastic anchor.

Corbin Russwin Hold Open PA Bracket

Corbin Russwin part # 509F49

Rubber Crutch Tips For 3/4" Round Chair Legs. This rubber chair tip fits a chair leg with a 3/4" outside diameter. Protect your floors from damage by using Rubber Chair Crutch Tips. Available in black or tan. Other sizes available. Easy to install, simply slide over your chair leg tubing. Great to use on chair legs, stools, tables and other applications where a heavy duty chair tip is needed. 

CRT75B BLACK

CRT75 TAN

Used on chairs and table, so you can use an adjustable height gilde. Used with the LA10625 or SLA12525. 1/4-20 Thread, 1" outside diameter and 7/8" inside diameter.

Chrome Plated Toilet Partition Flat Stop Keeper

Polished chrome plated Zamac construction. The keeper base is 2-1/2" tall by 1-3/32" wide. The latch face measures 2-1/2" tall with a 7/8" projection. The hole spacing is 1-1/2". The slot measures 5/16" by 1-9/16". Also known as a Bathroom Stall Keeper-Inswing Flat. Manufacture part # 5160.

Shipped with mounting screws.

Door Holder / Stop Rubber Shoe

Replacement Rubber Shoe
5/8" insert diameter
1" base diameter
7/8" overall height

Ives Part # HRT or FSPART.1075

Lyon Metal Locker Dome Washer 3/4" diameter with 1/8" hole. September 1981- Current. Also known as OP10549.

Medart Locker Lock bars. Used in 1972-1990. Includes 2 Lock rod springs.

Crash Chain Door Stop CS115

• Specially designed for full-size exterior doors.
• Tear resistant, grey vinyl cover.
• Heavy duty compression spring assembled to both ends of chain
  and end brackets.
• Packed with sheet metal screws.
• Cast Brass brackets with solid, welded steel chain.

Available in 20-1/2", 25-1/2" and 30-1/2" lengths. Length is determined
by the location of your door closer

PART # LENGTH
GCC205 20-1/2"
GCC255 25-1/2"
GCC305 30-1/2"

Toilet Partition Continuous One Ear Wall Bracket For 1" Panel Aluminum

Constructed of extruded anodized aluminum. Base is 2-5/8" wide by 57-1/2" long, with screw holes every 13" or so. The legs project out 2-3/4" with the thru hole at 2-3/8" from the back of the base. The legs have a clearance of 3/4" for 3/4" thick panels. Sometimes known as Bathroom Stall Continuous One Ear Wall Bracket. The manufacturers part numbers are 650-4031. These brackets are shipped with all the needed fasteners.