Search results for: 'spring for inside strip'

The Matte Black Hadrian Anchored Pilaster Shoe is constructed of stainless steel. Designed so that the shoe anchors directly to the ground and the pilaster sits inside. Is for 3/4" thick Pilasters and is 3" in height. Shoes come with fasteners to install and is available in different lengths.

Truth 22.10 Awning Window Operator.

Surface mounted Truth Awning Window Operator. The arms span 24-7/8" when in the closed postion. The mounting screws are 7" on center on the outside screw holes and 6" on center on the inside holes. Plastic Glides are not available separately, they are riveted in place.

Truth Part # 22.10

Von Duprin 88 Master Cam

This is inside the Von Duprin 88 Rim Device and is the piece that the key cylinder moves to lock and unlock the exit device.

Von Durprin part # 050501
Old Part # 951960

Toilet Partition Continuous Hinge 54" With 20 Degree Cam Close Stainless Steel. The hinges must be mounted flat when door is shut. For inside swing the hinges are mounted on the inside of the stall. For the outside they must be mounted on the outside.

Stainless Steel Construction, 14 gauge (.075" thick). Hinge is 3" wide when laid flat, by 54" long. Holes are spaced every 13" and are 9/32" diameter and 5 sets of holes. The hinge is self closing by a cam action, which is made possible by angle cuts on the continuous hinge leafs. Cam features 20 Degree Closing for ADA Doors. Can be raised up 3/8" for emergency entry. This hinge is also known as a Bathroom Stall Full Length Continuous Hinge. This hinge is non handed. Manufacture part # 130219, 7598, 125319, 650-9402.

Friction Ring Plastic Inserts For Round Legs with a 7/16" diameter friction ring casters only. 

Tubing Inside diameter / Part #'s

5/8" KK5A31
3/4" KK5A32
7/8" KK5A34
15/16" KK5A35
1" KK5A36
1-1/16" KK5A37
1-1/8" KK5A38

Plastic Chair Tips for Square Tubing Chair Legs. This tip is For a 1-1/4" Outside Diameter X 1-1/8" Inside Diameter  Chair Leg. Available in Black. 

Square Tubing Plastic Chair Tips for Square Chair legs with a  13/16" Outside Diameter X 11/16" Inside Diameter. PS81A has been replaced by KPSR81. Available in black only. 

Truth 16.18 Sash Lock.

Dimensions: 2-3/4" x 2-1/4" x 1"
2" between holes

#45098, 40242, 30386 and 31300 are sometimes found stamped inside the housing

The Matte Black Hadrian L Bracket is constructed of stainless steel and measures 1-1/2"Wx1-1/4"Hx2-1/2"L. It is recommended that 3 bracket be used for panels of 58" height. These are not designed to be through bolted together. Designed to be mounted on the inside of a partitions stall so hardware is not visible from the outside. Bracket comes with fasteners to install. Known as manufacturers part number 673411-BLK.

Rocker Type Square Plastic Chair Tip for Square Tubing Chair Legs with a 13/16" Outside Diameter X 11/16" Inside Diameter legs. For use on slanted square legs, available in black only. 

Plastic Chair Tips for Square Tubing chair legs with a 7/8" Outside Diameter X 3/4" Inside Diameter Legs. This tip is a rocker type tip for slanted square legs and available in black. 

The 7520R is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Round Nose, for Square Nose search 7520R. The treads are 1/8" thick along the entire depth of the treads, and have a nose that drops down 1-9/16".  The 7520R Round Nose is not available with the Grit Stripping. They are designed for interior use.

Square Plastic Chair Tips Square Tubing Chair Legs with a 3/4" Outside Diameter X 5/8" Inside Diameter Legs. This tip is a rocker type tip for slanted square legs and available in black only. 

International 5510S Rim Device-Light Duty

All devices are non-handed design
Auxiliary guarded latch deadlocks latch bolt automtically locks when the door is closed
High shock-resistant latching mechanical design or protection from vandalism
All inside components are made of high rust-resistant alloy or heavy electroplated steel

Standard 36”: Device length is 33 15/32” (850mm) for 3’ door use, with a standard push bar.
Long 48”: Device length is 44 3/4” (1137mm) for 4’ door use, with long push bar.

Flush Metal Partitions Nylon Cam

White nylon construction. The partition cam head outside diameter is 23/32" and the inside diameter is 1/2". The cams cylinder is 1-13/32" long with a diameter of 5/8". Also known as a Bathroom Stall Cam. Manufacture part # 98275.

Jackson 1085 Lever Arms

Replacement Lever Arm for the Jackson 1095 Active Housings.   This arm will only work on the 1095 Active Case!  Handing is determined by standing inside and looking out, if the arm in on the right hand side of the door, it is a right hand lever that you would order.

Jackson Part # RH 30-1247/LH 30-1248

White nylon construction. The partition cam head outside diameter is 23/32" and the inside diameter is 1/2". The cams cylinder is 1-13/32" long with a diameter of 5/8". For use with a 1/2" pintle. Also known as a Bathroom Stall Cam. Manufacture part # 98275.

Casement Window Operator 9" Arm

Replacement Casement Window Operator is made of a die cast housing and steel arm. The window operator housing has 4 mounting holes, 4-3/4" are the outside dimensions of the outside screws and 3-7/8" on the inside screws.

Right Hand Operator Shown in picture

Metal Based Swivel Chair Glide for a round tubing chair leg with a  5/8" O.D. X 1/2" I.D. This glide has a clip that holds the glide on by going inside the chair leg. The Chair Glides Base diameter is 1 1/4". 

The Corbin Russwin 677F02-9 Plastic Lever Spacer Ring has an outside diameter of .780 inches and an inside diameter of .730 inches.  The height is .345 of an inch, the flaired collar has an outside diameter of 1 inch. This bushing is used on the 900 Series Lever Trim on the ED4000 and ED5000 Series.

The Truth 22.18 Front Mount Awning Operator spreads 20-1/8 inches pin to pin on the arms when it is in the closed position. The Front Mount hole spaceing is 7 inches on the outside holes and 6 1/8 inches on the inside holes.

Doromatic retractor. The pinion rides inside this bracket to raise and lower the internal rods. Parts used with the retractor are the Pinion (G199005), Traveller (G199028) and the Pinion Bushing (G199046). Retractor measures 1-7/8" long by 7/8" wide by 1/4" thick.

Doromatic part # PB35 or RETRACT.101

Von Duprin 386NL Dummy Trim

This Von Duprin 386NL Night Latch Trim is just a pull handle. The bolt pattern of the trim plate lines up with the Von Durpin 33A on the inside so they are on conhesive unit. The base plate measures 7-15/16" by 1-5/8". The grip measures 8-1/2" by 4-5/16" with a 2-7/16" projection. This 386NL Night Latch Trim is handed. Uses a standard Rim Cylinder.

Doromatic 1590 Latch Bolt Assembly

Replacement Latch Bolt Assembly for the Falcon Doromatic 1590.   In the old days you could just replace the PB355 (SPRING.127) spring, but as of November 2015 you have to replace the complete latch head assembly.

Doromatic Part # 4270107603

Von Duprin Strike 304L

This Von Duprin Strike is used for the bottom latch of the 2227, 8827, 9827 and 9927. The strike measures 1-7/8" by 1-7/8" outside dimension of the square flange, with an inside dimension of 1-1/8" by 1-1/8". The part that is inserted into the floor is 1-3/8" x 1-3/8" and drops down 13/16". Also known as a Von Duprin Floor Mounted Mortise Strike.

Toilet partition pilaster shoes is designed to anchor directly to floor. Shoe is constructed of 20 gauge 304 stainless steel that is stamped and welded in a satin finish with square edges. Each shoe comes with fasteners and installation torx bit. Measurement is 3" tall and is designed to hold a pilaster that is 1" wide. Partition Pilaster will sit inside the shoe. This shoe is typically used with solid plastic partitions but could be used with different types of partition materials.

Metal Swivel Based Chair Glide with a round tubing leg measurements of  3/4" O.D. X 5/8" I.D. This chair glide does NOT feature a Ferrule, This glide has a clip that holds the glide on by going inside the chair leg. The Chair Glides Base diameter is 1 1/4". 

Wall Guard’s brushed stainless steel units measure 31.5”x15.5”x.06” and are designed to be installed under hand dryers. Provides protection for wall and makes clean up simple. Wall Guard can be used many different applications other than just under a hand dryer. Can be mounted around sinks, on restroom stalls or anywhere where to help prevent water damage. Known as World Dryers part number 37-10457K.

• Unit Size: 31.5”x15.5”x.06”
• Brushed Stainless Steel
• Mounted using Heavy Duty Double-Sided Adhesive Strips(Included)
• Easy Cleaning
• Modern Design

Toilet Partition Continuous Hinge 54" With Cam Close Stainless Steel. The hinges must be mounted flat when door is shut. For inside swing the hinges are mounted on the inside of the stall. For the outside they must be mounted on the outside.

Stainless Steel Construction, 14 gauge (.075" thick). Hinge is 3" wide when laid flat, by 54" long. Holes are spaced every 13" and are 9/32" diameter and 5 sets of holes. The hinge is self closing by a cam action, which is made possible by angle cuts on the continuous hinge leafs. Cam features Zero Degree Closing. Can be raised up 3/8" for emergency entry. This hinge is also known as a Bathroom Stall Full Length Continuous Hinge. This hinge is non handed. Manufacture part # 130209, 7599, 125319, 650-9402. This hinge is known as 7599.

American Sanitary Partitions Nylon Cam

Natural nylon construction. The nylon cam head diameter is 7/8" with an inside diameter of 11/16". The cylinder diameter is 3/4" and has an overall length of 1-11/32". For use with a 5/8" diameter pintle. Also known as a Bathroom Stall Door Hinge Cam. Manufacture part # 98245.

Monarch 19 Series Chassis Assembly Cover

This is the cover for the Monarch Falcon 19-R Rim Device. The cover measures 5-7/8" tall by 2-1/2" wide with a projection of 1-7/8". We sometimes find the number 6133 - 000 cast into the inside of the cover.

Monarch/Falcon part # 650384
Old Part # 6133

Double prong ceiling hooks are mounted to the inside top of a locker to hang a jacket, hat or other items. The locker hook is made of steel wire then zinc plated for a shiny finish 3/16" diameter. The dimensions top to bottom are 2-1/2" and 3-3/4" overall width. Between hole spacing is 1/2"-1" slot. Also known as 91001, 9005, 81007, bu0112, lu125.

Non-fading superior aging properties make this oil, grease, chemical and stain resistant matting a popular item. Non-combustible; tear, cut, impact and ozone resistant; high tensile strength and elongation properties; single piece rolls. Use inside or outside. Round ribbed corrugations run lengthwise, easily cleaned with soap and water.

GREASE AND OIL RESISTANT — NO FABRIC

Pricing below is per linear feet, Black Only, Size is the Width

Fiat Partitions Top Door Insert For 1"

Chrome plated Zamac die cast construction. The hinge U insert has outside dimesions of 2-3/16" wide by 1-1/2" by 1" deep with tow holes 1/2" diameter. The inside distance between the U's is 1-1/16". Also known as a Fiat Bathroom Stall Door Insert Top 1". Manufacture part # 4800.

Von Duprin 386DT Dummy Trim

This Von Duprin 386DT Dummy Trim is just a pull handle. The bolt pattern of the trim plate lines up with the Von Durpin 33A on the inside so they are on conhesive unit. The base plate measures 7-15/16" by 1-5/8". The grip measures 8-1/2" by 4-5/16" with a 2-7/16" projection. This 386DT Dummy Trim is non handed.

10" Kickdown Door Holder / Stop Grand Standard

No roll pin at pivot point
Mallable with a pair of pliers
Rubber shoe held on by a screw
American Made
Zinc plated steel

made by Grand Specialties 610z

Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.