Search results for: 'fitting roller door horn'

Horn Bleacher Spring.

Horn Bleacher Spring, Left hand shown in picture.

Horn bleacher upper rod bracket.

Horn Bleacher Linkage Arm 22" left hand, Left hand shown in picture.

VINYL BACK COCOA MAT ROAD ROLLERS

Road roller mats are made with fibers from the almost indestructible outer husk of the coconut. These fibers are bonded into a vinyl backing. These vinyl back Road Roller Mats can be installed much easier than woven mats and can be easily cut to fit without the mat unraveling. If small holes are needed for installation, a sharp knife or punch will easily do the job.

Rollers are 32' 9" long and around 1-3/16" thick

Horn Bleacher Coiled Spring. 4-1/2" length.

The stop is in the center of the rod only, Horn bleacher stop.

Ives Roller Bumper Offset Ives RB470

RB471
Features:

• Constructed in heavy-duty cast brass.
• RB470 used where two doors open against each other to prevent damage

to the doors or hardware.

Roller Bumper Straight Arm 4" RB471

Features:

• Constructed in heavy-duty cast brass.
• RB471 is ideal for use in situations where doors meet each

other at approximate right angles (back to back).

Ives Roller Latch RL32

The Ives Roller Latch RL32 is constructed of Brass and Plated to your desired finish.  The body measures 1-1/8" wide by 2-1/4" high and 2-1/4" deep.  The roller is constructed of Nylon, and has an adjustable projection up to 1/2".  Fits a standard heavy-duty cylindrical lock cutout.

LCN Sentronic Roller

This LCN Sentronic Roller is used on all of the LCN Track Closers, and Sentronic Closers. Nylon wheel is 1-1/16" diameter by 3/8" thick. The shaft is has a 1/2" diameter by 1-1/8" long. LCN part # 4040SE-3034.  

LCN Started using this Roller Assembly in December 2018.

Horn bleacher lower rod bracket.

Horn Bleacher Spring, Left hand shown in picture.

Horn Bleachers Vertical Push Rod Spring, Push rod spring only.

Von Duprin 5654 / 5754 Top Fitting and Cover

THe Von Duprin 050135 Top Fitting and Cover for the 5654 and 5754 Mullions.   Package includes the Top Fitting and Cover, and all of the fasteners.

Von Duprin Part # 050135

Replacement Roller For Roller Bumper

Replacement wheel for the Roller Bumpers and Gravity Type Coordinators.
15/16" diameter wheel
7/16" wide wheel
3/16" diameter hub
Comes with replacement axle

Ives Roller Bumper Straight Arm 6" Ives RB472

Features:

• Constructed in heavy-duty cast brass.
• RB472 is ideal for use in situations where doors meet each

other at approximate right angles (back to back).

Von Duprin 5654 / 5754 Fitting Set

Von Duprin 5654 and 5754 Mullion Fitting Set, Part # 050130.   Set includes top and bottom fittings, all of the mounting screws.

Von Duprin Part # 050130

Horn Bleachers Vertical Push Rod, Push rod only. for right hand or left hand. 17-1/2" x 3/8". Works for right hand or left handed.

Von Duprin 5654 / 5754 Bottom Fitting

Von Duprin 050190  Bottom Mullion Fitting for the 5654 and 5754 Mullions.   The package includes the bottom fitting and all of the fasteners.

Von Duprin part # 050190

Von Duprin 1654/4754/4854/4954 Bottom Fitting

This is the Bottom Fitting for the 1654, 4754, 4854, and 4954 Von Duprin Mullions. Mounting Screws included.

Von Duprin Part # 050390

Hussey Bleacher Nylon Roller, 1-1/4" X 3/4" X 3/8".

Cubicle Track Snap Out Fitting, sold in pairs.

Medart Bleacher Metal Roller w/axle bolt-nut.

Von Duprin 1654/4954 Top Mullion Fitting and Cover

Replacement Top Mullion fitting for the Von Duprin 1654 and 4954 Removable Mullions.

Von Duprin Part # 050335 

Interkal Riser Roller. The black plastic roller dimension is 1-1/4" diameter by 1-5/16" by 1/2" center hole. Used with Interkal bleachers known as 400082.

Doromatic TD35 Roller Strike

Painted Black Finish

Doromatic Part # TD35 or 4270107393

Ives Roller Latch RL30

The Ives Roller Latch RL30 is constructed of Forged Brass and Plated to your finish.   Furnished with a Nylon Roller.   Body measures 1" wide by 3-3/8" high by 1-11/16" deep. The roller has a maximum projection of 3/8" and is easily adjustable.

The concealed 2030 Series Pacer® is a heavy duty closer designed to fit in a narrow, minimum 1 3/4” aluminum transom. The single lever arm and roller assembly provide smooth, quiet door control and the choice of finishes and track functions meet virtually all architectural requirements.

Specifications

• Standard 2030 series closer shipped with standard arm, standard track, mounting/finish plate, and wood and machine screw pack
• Sized cylinders for interior doors to 4’6” and exterior doors to 3’6”
• Handed for right or left swinging doors
• Aluminum frame requires minimum 1 3/4” (44 mm) x 4” (102 mm) tube
• Closers to meet ADA requirements
• Standard or optional custom powder coat finish
• Optional plated finish on arm, fasteners and finish plate

Ives Roller Latch RL1130

The Ives Roller Latch RL1130 is a combination of the RL30 and an Angle Stop.  Tension is easy to adjust with the two tension screws on the face plate.

Cabinet Roller Catch.  Roller catches type b. Strike catch with polyethyleine roller. Size: 1-1/4" x 1-3/4" x 3/8", and the screws included.

Medart Lock Rod Roller Only for Lockers, manufactured in the usa. Also known as 50501, 1555, 80017, me55165, lmd933.

Claridge Roller Bracket for 2 map rail. Constructed of Extruded Aluminum. Use to display maps and other visual aids without ruining your materials.

Ives RL32 Nylon Roller RLPART.1045

This replacement Nylon Roller and Rivet Package is for the Ives RL32 Roller Latches.  The Roller measures 3/4" high by 5/8" diameter.  The Rivet measures 15/16" long and is threaded on one side.

Ives Part # RLPART.1045

Ives RL30 and RL1152 Nylon Roller RLPART.1025

This replacement Nylon Roller and Rivet Package is for the Ives RL30 and RL1152 Roller Latches.  The Roller measures 3/4" high by 5/8" diameter.  The Rivet measures 1-1/16" long and is threaded on one side.

Ives Part # RLPART.1025