R. C. Musson

Lower cost production for multi-family dwellings, apartment houses, low income housing. This vinyl stair tread with extra long nose is designed to use on a 2” x 12” plank step or molded concrete step. Heavier thickness at front “wear area”. They are designed for interior use.

Features:

• Extra long square nose
• Easy installation
• Easy clean
• Meets Fed. Specs. RR-T-650E Type B
• Contains no asbestos fiber
• Made of first quality homogeneous vinyl
• Color throughout thickness
• Free from imperfections which might lessen serviceability

Specifications:

• 355 Koroseal vinyl rib design stair treads by Musson Rubber
• Thickness: 1/8”
• Depth: 12”
• Nose: 1-3/4”
• Sizes available: 18”, 24”, 30”, 36”, 42”, 48”, 54”, 60”, 72”, 84”, 96”
• Colors available: Brown, Sand, Gray, Black

Designed for use in apartments, urban renewal housing, housing for the elderly and housing projects. Lower initial cost, ease of installation and cleaning, and long service appeals to owner and builder. Extra thick at front; Meets Fed. Specs. RR-T-650E Type B. They are designed for interior use.

Features:

• Extra thick at front
• Easy installation
• Easy clean
• Meets Fed. Specs. RR-T-650E Type B
• Contains no asbestos fiber
• Made of first quality homogeneous vinyl
• Color throughout thickness
• Free from imperfections which might lessen serviceability

Specifications:

• 375 Koroseal vinyl rib design stair treads by R.C. Musson
• Thickness: 3/16"
• Depth: 12"
• Nose: 1-1/4" square or curved
• Sizes available: 18", 24", 30", 36", 42", 48", 54", 60", 72", 84", 96"
• Colors available: Brown, Sand, Gray, Black

Improve safety and prevent worn carpet edges on steps; for new or renovation work. Butt 1/4” to 3/8” thick carpet against both the top and bottom lips of butt-type carpet nosing. Standard 8’ lengths; easily cut to size. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.140 Koroseal Vinyl Ribbed Carpet Nosing; 3-1/8” deep; 2-1/2” nose depth; square adjusta-nose. Lap 5/16”, 1/4" or 3/8” carpet over lip on both the step and riser. Select from standard colors of black, brown.

Shipping:   Due to shipping costs, this product is shipped in two 48" sections

FLUFF-CORD STRIP TILE-CONTINUOUS STRIP

A close-nap carpet-like surface of specially processed rubber-fabric strips made from recycled heavy-duty truck and bus tires; Natural Earthtone Gray Color. Strips are heat bonded to a woven flexible backing. This creates a "dry-back" adhesive back that reacts with our non-flammable adhesive to form a stronger bond to the floor. Install this permanent entry floor mat inside or outside; cord strips act as a wiper where dirt or moisture is a problem; are non-skid, non-absorbing, resist shrinkage, deaden sound. Ideal for heavy wear areas in shopping centers, lobbies, entryways, ramps, airports, etc. Produced in longitudinal rolls 12" wide x 25' long.

Tile must be installed using manufacturer's specific installation instructions and Musson No. TT-390 Non-Flammable Environmentally Safe Adhesive.

Order Fluff-Cord Strip Rolls here

400 Vinyl Stair Treads

Heavy gauge sharp-rib design Koroseal vinyl treads for heaviest traffic; 1/4" thick at wear area, easily trimmed to cover and fit any stair step. Install over concrete, metal, wood, terrazzo. Extra heavy thickness at the front "wear area". Meets Fed. Specs. RR-T-650E Type B. They are designed for interior use.

SPECIFICATIONS:

No. 400 Koroseal vinyl rib design stair treads 1/4" thick 12" deep; 1-1/4" square nose; contains no asbestos fiber; made of first quality homogeneous vinyl, color throughout thickness; free from imperfections which might lesson serviceability. Select standard length of 24", 30", 36", 42", 48", 54", 60", 72", 84" or 96". Select standard solid colors of Brown, Sand, Gray or Black.

GS365 Vinyl Stair Treads
The economical, nonporous, abrasion resistance and easy cleaning features of Koroseal Vinyl Stair Treads are now combined with the safety features of “Grit-Strips” into one stair tread. Can be used in all but the heaviest traffic areas. Meets Federal Specs. RR-T-650E Type B.

SPECIFICATIONS:

Furnish and install No. GS365 Koroseal Vinyl Stair Treads
Grit-Strip rib design stair treads; 7/32" thick, 12" deep; 1-1/4" square nose; two black* 1" wide abrasive Grit-Strips inlaid in tread, 1” from front edge, spaced 1-1/4" apart; contains no asbestos fiber; made of first quality homogenous vinyl, color throughout thickness; free from imperfections which might lessen serviceability. Select standard length of 36", 42", 48", 54", 60", 72", 84" or 96". Select standard solid color of Brown or Gray.

Non-fading superior aging properties make this oil, grease, chemical and stain resistant matting a popular item. Non-combustible; tear, cut, impact and ozone resistant; high tensile strength and elongation properties; single piece rolls. Use inside or outside. Round ribbed corrugations run lengthwise, easily cleaned with soap and water.

GREASE AND OIL RESISTANT — NO FABRIC

Pricing below is per linear feet, Black Only

Ribbed Koroseal Vinyl lap-type nosing for front edge of stages, bowling lane steps, platform-like floors and bar foot rests. Form fitting adjusta-nose; has a 7/8” lip to allow 1/8” flooring to lap over back edge. Standard 8’ lengths. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.105 Service Weight Koroseal Vinyl Ribbed Lap-Type Nosing; 2-3/4” deep; 1-1/2” nose depth; square adjusta-nose. Lap 1/8” flooring over the back lip to butt against ribbed design. Select from standard colors of black or brown.

Shipping:   Due to shipping costs, this product is shipped in two 48" sections

405CR Vinyl Stair Tread Risers

Plain color cove risers match Koroseal vinyl stair treads; or use a contrasting riser with vinyl or rubber treads; easily trimmed in height and length; savings in installation are substantial; cove risers are same sizes as stair treads.

SPECIFICATIONS:

Furnish and install No 405CR Koroseal vinyl coved stair riser; 1/8” thick, 7” high with 5/8” toe; ribbed back. Select standard length of 18”, 24”, 30”, 36”, 42”, 48”, 54”, 60”, 72”, 84” or 96”. Select standard solid color of Brown, Sand, Gray or Black.

Interlocking 1/2" x 11-7/8” x 11-7/8” recycled PVC tiles with bristle carpet inserts. Brushes off sand, dirt and slush from shoes and cart wheels; open grid drains away water and debris. Modular 11-7/8” x 11-7/8” tiles allow flexibility and the ability to fit the product to any size area. Tiles snap together easily to install and replace. Beveled ramp edges are available for non-recessed applications.

This product is part of our sustainable development program where the tiles can be returned at the end of the lifecycle for a credit toward replacement product. The material is then cleaned, ground, treated for contaminants in an environmentally safe process, and re-formed into new matting. Check with our customer service department for details.

Ribbed Koroseal Vinyl butt-type nosing for front edge of stages, bowling lane steps, platform-like floors and bar foot rests. Grooved cutting guides provide “cut-offs” to match flooring thickness. Standard 8’ lengths; easily cut to size. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.101 Heavy Duty Koroseal Vinyl Ribbed Butt-Type Nosing; 3-1/2” deep; 1-5/16” nose depth; square adjusta-nose. Cut nosing at proper guide to butt against 1/8” (or 3/16” or 1/4”) flooring. Select from standard colors of black or brown.

Shipping - Due to shipping restrictions, this product ships in two 48" long pieces.

DR-CT DIAGONAL RIB CARPET TILES
An attractive and functional entrance matting alternative; heavy duty modular carpet tile with excellent scraping and dirt removal properties for high traffic areas. Designed for interior use in entrances, vestibules, lobbies, between double doors, on ramps or in elevators.

Install in a recess or on the surface. Our easy release adhesive allows you to remove worn or damaged tile which is easily re-adhered. Tile can be switched to decrease traffic patterns; lasts longer, looks better. Vinyl or Aluminum beveled edging available.

3/8" thick; 19-11/16" x 19-11/16" square tile; diagonal rib pattern woven of 100% polypropylene pile yarn with a bitumen backing.

SPECIFICATIONS--No. DR-CT

DR-CT Diagonal Rib Carpet Tiles made of 100% polypropylene pile yarn with a bitumen backing in areas as indicated on drawings. Tile shall be of first quality commercial grade carpet, free of surface defects. Install tile in an alternating rib parquet pattern in indicated recess with recommended easy release adhesive, (or on surface area using vinyl edging or aluminum beveled frame). Tile shall be 3/8" thick, 19-11/16" x 19-11/16" square carpet tile. Select from standard carpet colors of Cranberry, Blue, Beige, Teal, Gray, Chocolate or Charcoal.

one DR-CT Diagonal Rib Carpet Tile covers 2.69 square feet

Adhesive specifically designed for the TT-12 Fluff Cord Tile.

1 gallon covers approximately 100 square feet

Adhesive information

DIRT CATCHER TILE DC225

A heavy-duty tile packed with 60 ounces of 100% solution dyed polypropylene is ideal for any entrance area where extreme traffic occurs. This tile's unique dirt pocket configuration effectively removes and traps dirt and moisture.

The Dirt Catcher Tile comes with a 7 year wear warranty on flat surfaces and is permanently anti-static.

1/2" thick; 19-11/16" x 19-11/16" square tile. Each tile is approximately 2.69 square feet.

Sold only in boxes of 12 pieces. Pricing is for a box of 12 pieces.

BERBER TILES BT-220 ENTRANCE MAT

A heavy-duty, 40-oz./sq. yard needlepunch olefin tile that "breathes" so that moisture evaporates quickly. This 3/8" x 19-11/16" x 19-11/16" tile with a bitumen backing will not shrink or curl. The berber texture offers all the advantages of a heavy-duty wiper/ scraper with a custom carpet look.

Sold in cartons only of 12 tiles, enough to cover 32.3 square feet

See Color Chart under "More Views"

KT18 Vinyl Landing Tiles

Landing tiles are .120" thick by 18" x 18" and designed to go with all the vinyl stair treads.  Available colors are Shale and Amber.  Shale is for use with the Black and Gray treads, and the Amber is for use with the Brown or Sand color treads.

VINYL BACK COCOA MAT ROAD ROLLERS

Road roller mats are made with fibers from the almost indestructible outer husk of the coconut. These fibers are bonded into a vinyl backing. These vinyl back Road Roller Mats can be installed much easier than woven mats and can be easily cut to fit without the mat unraveling. If small holes are needed for installation, a sharp knife or punch will easily do the job.

Rollers are 32' 9" long and around 1-3/16" thick

Insures a perfect fit of entrance mats in recess. Heavy gauge 6063 T-5 extruded aluminum, precut at factory, ready to assemble on job. Eliminate field measurements and construction delays; order mats in advance for last minute "dropping in place".

Frames can be furnished with square ends for open-end recess or for mitering on job. Maximum length is 17'; straight connecting pins supplied for frames over 17'. If frame is factory mitered, all sides must be same position. If all sides are not the same position, miter on jobsite; cannot use corner pins; spot-weld corners.

Frame size ordered will be the finished size of the inside measurement of the frame where the mat fits.

Use Frames with either 3/8" or 1/2" thick Perforated Rubber mats; 7/16" thick Link mats; Track Strip mats; Quill-Tuft mats; Hi Traffic; Cobblestone Matting; Diagonal Rib Tile; Premier Tiles; Berber Tiles; Plush Tiles; Vinyl Back Cocoa mats or Fluff-Cord Strip Tile.

SPECIFICATIONS

No. RF-14
Furnish and install Musson Aluminum Recess Mat Frames of extruded aluminum 6063 T-5 in sizes indicated on drawings. Frame shall be pre-cut at factory, and supplied with aluminum corner pins and steel anchor keys. Install per manufacturer's recommendations to receive specified Musson Mat and to accommodate specified flooring material outside frame. Screed a cement base into interior frame area 7/16" below the floor level, using edge of frame as a guide. Install Frame Position “A”, “B”, “C”, or “H” as applicable.

BRONZE ANODIZED ALUMINUM FRAMES

Position “H” only. Medium Bronze color electrostatically applied in two steps to Position “H” Frame shown above. All other specifications remain the same.

A tough mineral-coated waterproof non-slip surfacing with a pressure sensitive adhesive back. Helps grip foot traffic, preventing slipping, easy to apply; use inside or outside. Rectangular sizes with rounded corners or in rolls cut to any length. We suggest priming surfaces with Musson Grit Strip Adhesive before applying. Ideal for entranceways, ramps and walkways, stairways, heavy traffic areas, work areas, loading docks, recreational vehicles, boats & docks, cafeterias, kitchens, coolers, around drinking fountains and ice machines.

Pre cut pieces on this page only

A tough mineral-coated waterproof non-slip surfacing with a pressure sensitive adhesive back. Helps grip foot traffic, preventing slipping, easy to apply; use inside or outside. Rectangular sizes with rounded corners or in rolls cut to any length. We suggest priming surfaces with Musson Grit Strip Adhesive before applying. Ideal for entranceways, ramps and walkways, stairways, heavy traffic areas, work areas, loading docks, recreational vehicles, boats & docks, cafeterias, kitchens, coolers, around drinking fountains and ice machines.

Black Rolls only on this page, see Grit Strip Colored Rolls or Grit Strip Precut

A tough mineral-coated waterproof non-slip surfacing with a pressure sensitive adhesive back. Helps grip foot traffic, preventing slipping, easy to apply; use inside or outside. Rectangular sizes with rounded corners or in rolls cut to any length. We suggest priming surfaces with Musson Grit Strip Adhesive before applying. Ideal for entranceways, ramps and walkways, stairways, heavy traffic areas, work areas, loading docks, recreational vehicles, boats & docks, cafeterias, kitchens, coolers, around drinking fountains and ice machines.

Use adhesive where Grit Strip is applied to porous surfaces such as wood or concrete. Grit Strip adhesive is recommended as a sealer; will give a better, longer lasting bond. Recommended application temperature is 60 degrees and above. One quart covers approximately 50 square feet (single coat) of Grit Strip; available in quart and pint units.

Adhesive information

GSA11 ALUMINUM STAIR TREADS

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 11" model here.

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 9" model here.

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 7-1/2" model here.

Corner Guard CG-20 2" x 2"

90 degree 2” x 2” vinyl corner guard with aluminum retainer.  Vinyl flex action absorbs impact, and is .085” thick, the aluminum retainer is .062 thick.  Each corner guard includes the end caps.  Available in 4, 8 and 9 foot lengths.  Corner guards are shipped with a top and bottom end cap.

Corner Guard CG-10 3" x 3"

90 degree 3” x 3” vinyl corner guard with aluminum retainer.  Vinyl flex action absorbs impact, and is .100” thick, the aluminum retainer is .062 thick.  Available in 4, 8 and 9 foot lengths.  Top and bottom end caps included with the corner guard.

A non-solvent based alternative to install rubber and vinyl stair treads and cove risers to concrete, wood, terrazzo, metal or marble. One gallon covers 75 lineal feet of stair treads (brush on back of tread and step). Ready to use in 1 quart, 1 gallon and 4 gallon containers.

Adhesive information

For bonding to all Disc-O-Treds, Rubber Stair Treads or Koroseal Vinyl Stair Treads to concrete, pan filled, wood, metal, marble and terrazzo steps. A rapid drying, long range contact cement; specially formulated for Musson stair coverings. Brush on application; use on back of treads and back of nosing. Contains solvents, extremely flammable. 1 gallon covers 75 lineal feet of stair treads (brush on back of tread and step). Ready to use in 1 quart, 1 gallon and 5 gallon containers.

If ordering the gallon or 4 gallon pail, it will ship via freight truck. If you would prefer something that ships Fed Ex Ground, please order the 300 Stair Tread Adhesive.

Adhesive information

For installing Rubber Floor Tiles or Rolls over suitable on-grade dry concrete floors, suspended concrete floors, or suspended wood floors. May also be used with sanded back molded rubber stair treads. Not recommended where excessive moisture exists; Non-Carcinogenic; Non-Toxic; safe for the environment and freeze thaw stable. See label for complete instructions. Ready to trowel in 1 gallon or 4 gallon cans. Covers 150 square feet per gallon.

Adhesive information

775 EPOXY FLOORING ADHESIVE

The only recommended adhesive for use with Disc-O-Tile. May be used with other rubber stair treads, tile and flooring. Because of flame spread properties, other adhesives will not bond Disc-O-Tile to the floor. A two-part solvent-free adhesive; contains 1 can Part A 1 can Part B, and a stirring paddle. Covers approximately 150 square feet per unit. Enviromental Friendly!

Adhesive information

STAIR TREAD MOUNTING TAPE

Speeds installation of vinyl stair treads without the mess! Tape is sold in 4" wide rolls of 164 feet.

We recommend two strips of tape per tread. One on the nose and one at the back. As an example for the 36" tread you would need 72" or 6' of tape.

320 CARPET TILE ADHESVIE

A special latex emulsion pressure sensitive adhesive formulated for installation of modular carpet tiles or carpet matting. Adhesive is non-flammable, water resistant and has excellent resistance to vinyl plasticizer migration. Adhesive remains tacky for an extended period - allows tile to be picked up and replaced without affecting adhesive. Remove tiles from floor more easily than with conventional adhesives, simplifying reinstallation of tile sections or a complete area.

Covers 200 to 300 square feet per gallon
Sold in 1 or 4 Gallon Pails