Search results for: 'reinforced rubber table tip 1 1 8'

Bleacher Axle Pin 2" x 1/2" with clip used with 3-1/2" universal bleacher wheel.

Plate Top Single Wheel Caster - Swivel - 5" Wheel, 1-3/4" x 3"" Hole Spacing. Ball bearing swivel, zinc finish with a black rubber wheel. Hard tread and soft tread caster available for both carpet and non carpet areas. 

KK9C61 hard tread for carpet

KK9C62 soft tread for non carpet surface

Hadrian Wall Mounted Privacy Screen's with pedestal for extra strength. Powder coated are available in 58" heights by 18" or 24" wide. Standard chrome brackets with pedestal are included. Wall hung screens are great for between urinals or a sink and urinal. All colors ship out in 12 business days, then 2-4 day travel delivered any where in the usa. we also offer continuous aluminum and stainless steel brackets for extra support.

Hadrian Color Chart

Hadrian Instructions Powder Coated

Hussey Bleacher Gearbox Reducer 60:1. used with 1/2hp motor. Includes adapter plate for older power trac III.

Hussey bleacher 1/2 horsepower, Three phase, rpm 1725, 208 volt, Note this is commonly used with 70:1 or 60: 1 Hussey gearboxes. Used with for Power III & Power Trac IV.

Non-Swivel Leveler Threaded Stem Glide with metal base. Thread is 1/4-20, Base Diameter is 1 1/16" and the stem length is 1". This glide screws into a 1/4" threaded leg hole to put a selected height. Use this product to stop wobbling on an uneven floor. 

1/4-20 Threaded Leveler with a Felt Base to be screwed into a 1/4" threaded hole in furniture leg. You can also combine with a t-nut to use in wooden furniture. Base Diameter and Stem Length are 1" on this glide. 

Comtec Toilet Partitions 8" Ada Hinge Set, 3 Hinges Total. Clear anodized aluminum for 1" panel and 1" door. Used by every Bathroom Toilet Stall manufacture on Solid Plastic Toilet Partitions Doors. Manufacturer part #'s 7978, 7988, 8974, 8984. These hinges are reversible by taking the 3 pieces apart and reconfiguring the opposite swing.

Partition Keeper Bumper Inswing 1" Post Square Edge Cast Stainless Steel

Cast stainless steel construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. The slot is 5/16" deep by 1-1/2" high. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing 1". Manufacture part # 5623.

Shipped with mounting screws.

Ives Plunger Type Holder FS1154

Features:

• Constructed from heavy-duty cast brass or bronze.
• Plunger and internal parts are plated steel and provides a 1-1/4" throw for all types of doors.
• Plunger is easily activated with minimal pressure, releasing instantly with a light tap on the platform lever.
• Round non-marring rubber shoe is securely fastened with a screw in flanged cup to prevent movement or loss. When worn, shoes are easily replaced.

Ives Part # FS1154

Partition Keeper Bumper For 1" Square Post Outswing Cast Stainless Steel

Cast stainless steel construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Outswing 1". Manufacture part # 5723.

Shipped with mounting screws.

American Sanitary Partition Bottom hinge Insert For 1" Door

Chrome plated Zamac die casting. The door insert outside measurements are 2-5/16" wide by 1-5/32" deep by 1-3/16" tall. The inside dimensions are 1" and the hex hole measures 3/4". The round hole measures 5/16". Also known as a Bathroom Stall Door Insert - Bottom 1". Manufacture part # 2490

Actuator 4-1/2" diameter, with blue engraved lettering.

Double Hook Chrome Plated Projects 3-1/2", 4-1/2"ht

Friction Ring Single Wheel Caster - 2" Wheel - 7/16" Stem Diameter, 1" stem length, 2" wheel diameter. Zinc finish with black rubber wheel. Available with tread for carpet and without carpet. 

KK5711 hard tread for carpet

KK5712 soft tread for non carpet

Toilet Partition Aluminum Square Post 1-3/4" X 10'

Extruded anodized aluminum. 1-3/4" x 1-3/4" x 10' long. Also known as a Bathroom Stall Aluminum Square Post. Manufacture part # 40-5443400G. Oversized part, has to ship Truck.

Sargent 700 ET Spindle Kit 730-7

This Sargent Kit 730-7 includes the spring, spindle and the associated plates. Look under "More Views" for a detailed look of this repair kit. The 730-7 is for 1-3/4" doors.   Shank measures 4-1/4" long, square spindle is 5/16" square.

Sargent Part # 730-7

Headrail End Plug 1"X2"H

Chrome plated Zamac die cast construction. The head rail end plug measures 1" wide by 2" tall. Also known as a Bathroom Stall Head Rail End Plug. Manufacture part # 6670.

Comtec Toilet Partition Aluminum 6" Outswing Strike And Keeper For 1" Post Or Pilaster

Clear Anodized aluminum construction. Strike and Keeper is 6" high by 1-15/16" wide. The three mounting screws are 2" on center apart. Also known as a Bathroom Stall Strike and Keeper outswing1". Used mostly on Solid Plastic (HDPE) Toilet Parttions. Known as 5878.

Shipped with mounting screws.

#12 X 2-1/2" Screw 6 Lobe(T-27), Chrome, 1/2" diameter head, also known as a 91903. This uses a Torx bit to drive screw.

Plate Top Single Wheel Caster - Swivel - 3" Wheel, 13/16" X 1-9/16" Hole Spacing, ball bearing swivel. Zinc finish with black rubber wheel. Available with tread for carpet and non carpet surfaces. 

KK9B41 hard tread for carpet

KK9B42 soft tread for non carpet surface

Kit includes rod with exposed flanges.

Flanges fabricated of 20ga. stainless steel with a satin finish. Flanges have (3) countersunk 13/64" dia. holes to accept #10 flat or oval head screws furnished by others.

Rod is installed in straight section between two (2) mounting flanges. Rods longer than 60′′ require ceiling hanger Model No 1204-C18.

For use with standard shower curtain model No ’s 1200 or 1200-V having 60′′ length and standard hooks Model No 1200-SHU unit should be installed with rod centerline 74-1/2′′ AFF or 67′′  above tub rim to obtain 6′′ bottom overlap.

Partition Anti-Grip Headrail 1" X 95" Type B Aluminum

Extruded anodized aluminum construction. The cross section measures 2-3/4" high by 1-3/32" by 95" long. The part that fits on top of the pilaster is 1" wide by 3/4" deep. The wall thickness on this part is 3/64". Also known as a Bathroom Stall Headrail. Manufacture part # 80042.

This product is usually used on Solid Plastic (HDPE) Toilet Partitions.

Chair Glide for a square leg chair with tubing outer diameter 3/4" and inner diameter of 5/8". 1 1/16" Base diameter. This glide does not have a ferrule.  

Plate Top Single Wheel Caster - Swivel - 4" Wheel, 1-3/4" x 3"" Hole Spacing. Ball Bearing Swivel with a zinc finish and black rubber wheel. Available with a tread for carpet and non carpet surfaces. 

KK9C51 hard tread for carpet

KK9C52 soft tread for non carpet surface

The Swivel Glide 5/8" Outside Diameter with Ferrule Outside Holding Clip is used on American Desk, Artco Bell, Carter Craft, Krueger, Peabody and Virco Chairs. Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the out side of the leg, see more views for picture of outside holding clip.  This product will git all 5/8" outside diameter tubing.  The base has an 1-1/4".

Bobrick Toilet Partition Keeper Bumper For 1" Outswing Square Edge Post

Polished chrome plate Zamac die casting construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Outswing 1". Manufacture part # 5720.

Shipped with mounting screws.

The Matte Black Hadrian 1/2" Pedestal Support Brace is constructed of stainless steel. Pedestal support brace is used in place of a traditional pilaster where the pilaster anchors to the ground. This pedestal support brace allows pilasters to be off the ground but still provide structure to partitions. Designed to be used under a pilaster or panel that is 1/2" thickness. Available in 12", 9" and 4" heights and comes with fasteners for installing. Known as manufacturers part number 673441-12AF-BLK, 673441-9AF-BLK and 673441-4AF-BLK.

Actuator 4-1/2" diameter, with blue engraved lettering with text.

Partition Door Piano Hinge 57", 14 Gauge SS,1/4" Pin with 20 Degree Cam Close. This hinge keeps the door open 20 degree so the user knows there is nobody in the restroom toilet stall. This is the most Heavy Duty Continuous Full Length Hinge we sell. 14 gauge (.075" thick) stainless steel construction with a 1/4" diameter hinge pin. The hinge leafs are angle cut so your door will close with the camming action. The hinge is 3" wide when laid flat, and 57" long. Screws are spaced 11" apart and the holes are 9/32" diameter and has 6 sets of holes. Hinge can be raised up 3/8" for emergency entry. Also known as a Restroom Toilet Stall Full Length Continuous Hinge. Manufacturer part #650-9401 and 160039. The hinges must be mounted flat when door is shut. For inside swing the hinges are mounted on the inside of the stall. For the outside they must be mounted on the outside.

The Von Duprin 99 rim exit devices for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The Von Duprin 98 device has a smooth mechanism case and the Von Duprin 99 device has a grooved case. The rim device is non-handed.

Ships with all the mounting screws and the 299 Strike.

Glynn-Johnson 79 Series Overhead Door Holder Surface Mounted

Glynn-Johnson 70 and 79 series models are constructed primarily of Brass and 300 series Stainless Steel substrates, with several components fabricated of Steel treated to resist corrosion. Models in the 70 series utilize a 1/2"-diameter stainless steel bar, while the 79 series uses a 3/4" stainless steel bar. The bar is always provided in US32D. The spring, washer and nut are provided in a clear zinc finish.

GJ70-79 Catalogue